Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
2 Installation Drainage connections A B A. Connect the drain hose, without kinking it, to a draining duct or a wall drain fixed at a height between 65 and 100cm from the floor. B. Alternatively, place it over the edge of a basin, sink or tub, fastening the hose supplied to the tap. The free end of the hose should not be under water. ! We advise against the use of hose extensions. In case of absolute need, the extension must have the same diameter as the original hose and must not exceed 150cm in length. Electrical connections Before plugging the appliance into the mains socket, make sure that: . The socket is earthed and in compliance with the applicable law. . The socket is able to sustain the appliances maximum power load indicated in the Technical Details table (on the right). . The supply voltage is included within the values indicated in the Technical Details table (on the right). . The socket is compatible with the machines plug. If this is not the case, replace the socket or the plug. ! The machine should not be installed in an outdoor environment, not even when the area is sheltered, because it may be very dangerous to leave it exposed to rain and thunderstorms. ! When the machine is installed, the mains socket must be within easy reach and should be connected to a suitable electrical supply. ! Do not use extensions or multiple sockets. ! The power supply cable must never be bent or dangerously compressed. ! The power supply cable must only be replaced by an authorised serviceman. ! The company denies all liability if and when these norms are not respected. The first wash cycle Once the appliance has been installed and before you use it for the first time, run a wash cycle without detergent and no laundry, setting the 90°C programme without a pre-wash cycle. Technical Details Models A1637 A1437 A1237 59.5cm wide Dimensions 85cm high 60cm deep Capacity from 1 to 7kg Wash Electric voltage 220/240 Volts 50Hz connections maximum absorbed power: 1700W-2100W Water maximum pressure 1 MPa (10 bar) connections minimum pressure 0.05 MPa (0.5 bar) drum capacity 54 litres Spin Speed up to 1600 rpm -A1637 up to 1400 rpm -A1437 up to 1200 rpm -A1237 Control programme 3 programmes temperature 60°C according to -run with a 7kg load IEC456 directive This appliance is compliant with the following European Community Directives: - 73/23/EEC & 93/68/EEC (Low Voltage) and subsequent amendments. - 89/336/EEC,92/31/EEC & 93/68/EEC (Electromagnetic Compatibility) and subsequent amendments. GB 3 Washing Machine Description Control panel GB START/STOP Button Programme key LEDs Detergent dispenser TEMPERATURE Knob SPIN SPEED Knob FUNCTION Buttons PROGRAMME Knob ON-OFF/DOOR LOCK LED START/RESET Button Detergent dispenser: To add detergent and fabric softener (see Detergents and Laundry). Programme key: To consult a straightforward chart of the different programmes available. Pull the grey tab outwards to open it. LEDs: To find out which wash cycle phase is under way. If the Delay Timer function has been set, the time left until the programme starts will be indicated (see next page). SPIN SPEED knob: To set the spin speed or exclude the spin cycle completely (see Personalisation). FUNCTION buttons: To select the functions available. The button corresponding to the function selected will remain on. TEMPERATURE knob: To set the temperature or the cold wash cycle (see Personalisation). START/STOP button: To turn the washing machine on and off. START/RESET button: To start the programme or cancel any incorrect settings. ON-OFF/DOOR LOCK LED: To find out whether the washing machine is on and if the appliance door can be opened (see next page). PROGRAMME knob: To select the wash programmes. The retractable control knob: press the centre of the knob for it to pop out. The knob stays still during the cycle. 4 Washing Machine Description LEDs: The LEDs provide important information. This is what they tell you: Cycle phase under way: During the wash cycle, the LEDs gradually illuminate to indicate the cycle phase is under way: Note: during draining, the LED corresponding to the Spin cycle phase will be turned on. Function buttons: The FUNCTION BUTTONS also act like LEDs. When a function is selected, the corresponding button is illuminated. If the function selected is incompatible with the programme set, the button will flash and the function will not be enabled. If you set a function that is incompatible with another function you selected previously, only the last one selected will be enabled. ON-OFF/DOOR LOCK LED: If this LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damage. Wait for the LED to flash before you open the appliance door. ! The rapid flashing of the ON-OFF/DOOR LOCK LED together with the flashing of at least one other LED indicates there is an error. Call for Technical Assistance. Additional feature - Models A1637 & A1437 only: Your machine has a delay Timer function and ...
Este manual também é adequado para os modelos :Máquinas de lavar - A1437 (473.24 kb)
Máquinas de lavar - A1637 (473.24 kb)