Assessments - 3, GPA: 4.7
(
)
)
|
Fotos e especificações LG WD-12480N |
Facilidade de uso
26 GASKET ASSEMBLY GASKET ASSEMBLY Take apart the cabinet gasket clamp. Unscrew 2 screws from the cabinet cover. Open the lower cover cap and unscrew 1 screw inside. Take apart the lower cover. Disassemble the cantrol panel. (refer to the page 25) Unscrew all the screws on the upper and lower sides of the cabinet cover. Take apart the tub gasket clamp. Make sure that the drain hole of the gasket is put beneath when reassembling the gasket. Refer to the arrow mark on the tub cover. 27 28 Remove the back cover. Take off the belt turning the pulley. Unscrew the bolt to pull out the pulley. Unscrew 2 screws from the bracket. Push the motor in the arrow direction for disassembling. When reassembling the motor, make sure that motor mounting bushings are not taken off from the bracket. Pull out the hinge, pressing its snap. Do not use the pulled - out hinge again. It may be taken off during operation. Hinge, Damper Damper 1 2 3 PULLEY, MOTOR, DAMPER (PULLEY) (MOTOR) (DAMPER) Open the lower cover cap (..) by using a coin. Turn the drain plug (..) to pull out the hose. Unplug the drain plug ( .. ) , then the water flows out, At this time use a vessel To prevent water from flowing on the floor. If the water does not flow any more,turn the pump filter ( .. ) open to the left. Take out any foreign material from the pump filter ( .. ). After cleaning, turn the pump filter(.. ) clockwise and insert the drain plug ( .. )to the original place. close the lower cover cap. Clean the drain pump filter 1 100 2 3 2 3 PUMP PUMP Pump Outlet Hose Tub Pump Bellows Remove pump outlet hose. Remove tub pump bellows. Remove cap (Remaining Hose.) Disconnect the wiring. Unscrew 2 screws. Remove the pump. Loosen the M6 heater nut to pull out the heater. When mounting the heater, be sure to insert the heater into the heater clip on the bottom of the tub. Pull it out by holding the thermistor bracket. If it is pulled by the wire, it may be broken. When mounting the thermistor again, make sure that it is got back tight to the bushing. HEATER THERMISTOR CAUTION 29 SWITCH ASSEMBLY, DOOR LOCK SWITCH ASSEMBLY, DOOR LOCK Take apart the cabinet cover clamp and release the gasket. Unscrew 2 screws holding the door lock. Disconnect the door lock from the wiring connector. WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB Remove the heater. Remove the foreign material (wire, coin and others) by inserting a long bar through the hole. 30 31 10-1.THE EXPLODED VIEW OF CABINET ASSEMBLY 10. EXPLODED VIEW A152 A140 A153 A151 A150 A141 A131 A130 A134 A133 A276 A275 A277 A300 A270 A272 A271 A274 A273 A410 A485 A430 A100 A101 A110 A103 A104 A102 A440 A303 A310 A154 32 10-2 THE EXPLODED VIEW OF CONTROL PANEL & DISPENSER ASSEMBLY A450 F215 F110 F210 F225 F300 F120 F220 F432 F170 F160 F430 F441 F462 F322 F321 33 10-3 THE EXPLODED VIEW OF DRUM & TUB ASSEMBLY K311 K131 K130 K136 K135 K411 K410 F464 F320 F310 K140 K510 K346 K344 K342 K520 F468 K340 F466 K111 K110 K141 F467 K530 K330 K332 F461 K611 K610 K...
Este manual também é adequado para os modelos :Máquinas de lavar - WD-10480N (1.7 mb)
Máquinas de lavar - WD-10480NV (1.7 mb)
Máquinas de lavar - WD-10480S (1.7 mb)
Máquinas de lavar - WD-10481N (1.7 mb)