Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
F: 18 Detergent solution pump blocked; Clean the detergent solution pump -> page 10. Drainage hose / waste pipe blocked; Clean the drainage hose at the siphon -> page 10. F: 21 Motor fault. Call customer services. F: 23 Water in the base tub, appliance leaking. Call customer services. . Risk of electric shock. Disconnect the mains plug. . Risk of explosion. No solvents. 10 Maintenance Detergent solution pump Turn the programme selector to .........(Off) and disconnect the mains plug. 1. Open and remove the service flap. 2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it from the housing.Remove the container. Remove the sealing cap, allow the detergent solution to flow out. Replace the sealing cap and place the drainage hose in the retainer. 2* For models without a drainage hose: Carefully unscrew the pump cover until the detergent solution begins to flow out.When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. 3. Carefully unscrew the pump cover (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 5. Replace the pump cover and screw it tightly. 6. Place the service flap back on and close. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the ..........(Drain) programme. Drainage hose at the siphon Turn the programme selector to ......... (Off) and disconnect the mains plug. 1. Loosen the hose clamp, carefully remove the drainage hose (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the HydroSafe safety device in water (contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (apart from ..........n (Spin) / ..........(Drain)). 3. Choose ..(Start/Reload). Let the programme run for approximately 40 seconds. 4. Turn the programme selector to ......... (Off). Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter with pliers and clean. 2. Connect the hose and check for leaks. . Risk of scalding. Allow the detergent solution to cool down. What to do if ... . Water is leaking out. . Attach/repla. Tighten the ce the drainage hose correctly. screw connection of the supply hose. . No water supply. Detergent not dispensed. . $ (Start/Rnot selected. Tap not turn. Filter blocke. Supply hose eload) ? ed on? d? Clean the filter -> page 10. kinked or trapped? . Washing machine door cannot be opened. . Safety functi. (Rinse H. Can be opeon active. Programme stopped? -> page 4. old = ..... ........................... ............) selected? -> page 3, 4. ned by emergency release only? -> page 9. . Programme does not start. . $ (Start/R. Washing ma. Childproof loeload) or (Finished in) time selected? chine door closed? ck active? Deactivate -> page 5. . Detergent solution is not drained. . (Rinse H. Clean the de. Clean the wold = ..... ........................... ............) selected? -> page 3, 4. tergent solution pump -> page 10. aste pipe and/or drainage hose. . Water not visible in the drum. . Not a fault water below the visible area. . Unsatisfactory spin result. Laundry wet/too damp. . Not a fault spin cycle bDistribute sm. S (Easy-ir. Selected spthe unbalanced-load detection system has cancelled the ecause of uneven distribution of the laundry. all and large items of laundry evenly inside the drum on) selected? .> page 5. eed too low? .> page 5. . The programme length jumps during the final spin.. . Not a fault varying distrdisplay panethe number of spin cycles may be changed due to the ibution of the laundry, which may cause the time in the l to be corrected. . Spin cycle performed several times. . Not a fault unbalanced load detection system adjusts the imbalance. . Residual water in the compartment for care products. . Not a fault . Clean the inthe action of the care product is not affected. sert if necessary -> page 9. . Odour formation in the washing machine. . Run prograstandard detergent. mme ..F ........... (Cottons) 90 °C without laundry. Use . Status display... flashing. Appliance has detected a detergent overload. . Too much dIf foam is esMix 1 tablescompartmen. Reduce the etergent used? caping from the detergent drawer: poon of fabric softener with . litre of water and pour into t II (not with outdoor or down fabrics). detergent dosage for the next wash cycle. . Intense noise formation, vibrations and .wandering. during the spin cycle. . Are the applSecure the a. Trans...
Este manual também é adequado para os modelos :Máquinas de lavar - WAE24463BC/10 (1.78 mb)
Máquinas de lavar - WAE24463BC/12 (1.78 mb)
Máquinas de lavar - WAE24463BC/13 (1.78 mb)
Máquinas de lavar - WAE24463BC/14 (1.78 mb)