Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
3. Place covers over the transport bolt holes Four plastic covers are provided in the small parts bag included with your washer. Separate these covers and install one in each hole where the transport bolts were removed. Lock covers firmly by pressing on the snap hook. Insert hose holder. Secure hoses in the hose holders. NOTICE: Keep the assemblies together and store them for later use such as when moving the washer. Water connections Water supply hose connections NOTICES . The washing machine must only be operated with cold and hot (max. 140 °F/60 °C) tap water. Do not connect the appliance to the mixer tap of a pressurized hot-water boiler. . To prevent water damage, the hot and cold water valves should be accessible when the washing machine is in place and should always be turned off when the washing machine is not in use. . If installing the washing machine in a new building or a building in which the plumbing system was recently installed or upgraded, flush the lines before installing the washing machine to remove any sand, dirt or residue. . To prevent leakage or water damage, follow the instruction in this chapter. . If in doubt, have the appliance connected by a technican. Connect your washer to the wall faucets using the included AquaSecure water supply hose. Observe each of the following: . Only use the new water supply hose shipped with your washer. Never connect old used hoses. . The water supply hoses must not be kinked, bent or flattened in such a way as to potentially diminish water flow. . The water supply pressure must be between 14,5 to 145 psi (1 - 10 bar) with a minimum of 2.2 U.S. gallons (8 liters) of flow per minute. A pressure regulator valve must be installed if the maximum water pressure is exceeded. . Make sure the water supply faucet is easily accessible when the washer is in use. The faucet should be turned off if the washer is going to be unused for extended periods of time. . Make sure rubber washers are in place at both ends of the water supply hose. Missing washers could cause leaks. . The connection points are under full water pressure. Turn on the water tap and check for leaks. . Periodically inspect the water supply hose and replace with a new hose if cuts, kinks or leaks are observed. Water connection hoses . red - Hot water-hose . blue - Cold water-hose Attach this end to water tap. Hand tighten only. .................... .................... 14 Attach this end of the hose to the back of the washing machine. Hand tighten only. About the AquaSecure Hose The AquaSecure hose prevents potential flooding in the event the hose develops an internal leak. If the hose leaks, the indicator turns red and water flow is blocked. Water drain hose connection NOTICES . Do not reuse an old drain hose. Only use the drain hose and parts included with your washer. . Do not kink or modify the water drain hose. Height of drain point Height difference between the floor and drainage point: max. 39 in. (100 cm). Types of drainage hookups Standpipe Attach the drain hose using the elbow included with your washer. Fit the drain hose to the elbow provided leaving a maximum of 4 inches of drain hose projecting. Insert this section of the drain hose into the drain pipe. Secure the elbow and hose with a nylon tie strap or the equivalent to keep the hose from coming out of the drain pipe during use. Sink siphon Secure the drain hose to the sink siphon using a O 0.9 - 1.6 in. (20-44 mm) hose clip (available from a hardware store). Wash Basin 9 WARNING SCALDING When washing at high temperatures, there is a risk of scalding if you touch hot suds, e.g. when pumping out hot suds into a wash basin. Do not reach into the hot suds. 9 CAUTION APPLIANCE DAMAGE/DAMAGE TO TEXTILES If the end of the drain hose is dipped into the pumped-out water, water can be sucked back into the appliance and can damage the appliance/ textiles. Make sure that: . The sealing plugs do not seal the drain of the wash basin. . The end of the drain hose does not dip into the pumped-out water. . The water flows out fast enough. Attach the drain hose securely to the wash basin. NOTICE: In any multi-story installation, the washer should be installed on a drained floor to prevent water damage to rooms below in the event of a leak. .......... .................. ............ ........ Leveling the washer Electrical connection Importance of leveling the washer Your new washer uses high spins speeds to remove water at the end of the wash cycle. It is important that your washer is level and that all four washer feet press with equal pressure against the floor. This will help assure the quietest, most vibration-free use of your washer. Follow these steps: 1. Install the washer on a level and solid surface, preferably in a corner of a room. 2. If the floor is uneven (or unlevel) adjust the washer feet as required to level the washer. Do not place anything under the washer feet to help level the washer. 3. Extend the washer feet no more than is nece...