Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
page 11. ..: .... Water in the base tub, appliance leaking. Call the after-sales service. Other displays Switch off the appliance, wait for 5 seconds and switch it back on again. If the display appears again, call the after-sales service .. page 13. . Risk of electric shock. Disconnect the mains plug. . Risk of explosion. No solvents. 11 Information about blockages Detergent solution pump Set the programme selector to ....Off and pull out the mains plug. 1. Open and remove the service flap. 2. Remove the drain hose from the retainer. Remove the sealing cap, allow the detergent solution to flow out. Push the sealing cap back on. 3. Carefully unscrew the pump cover (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). 5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the drain hose in the holder. 6. Refit the service flap and close it. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and star the .. Empty programme. Drainage hose at the siphon Set the programme selector to ....Off and pull out the mains plug. 1. Release the hose clamp and carefully pull off the drain hose (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the HydroSafe safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except .. Rinse/Spin ..//.. Empty). 3. Press .. (Start/Add laundry). Let the programme run for approximately 40 seconds. 4. Set the programme selector to ....Off. Pull out the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter with a small brush. and/or on standard and Aquasecure models: Remove the hose from the rear of the appliance, Take out the filter with a pair of pliers and clean it. 6. Connect the hose and check for leaks. Risk of scalding. . Allow the detergent solution to cool down. . Turn off the tap. What to do if... . . . . . . . . . . . . . . . . . Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. No water supply. Detergent not dispensed. . $ (Start/Add laundry) not pressed? . Tap not turned on? . Filter blocked? Clean the filter a page 11. . Supply hose kinked or trapped? Washing machine door cannot be opened. . Safety function active. Programme cancellation? a page 4. . (Rinse hold = no final spin) selected? a page 3, 4. . Can be opened by emergency release only? a page 13. Programme does not start. . $ (Start/Add laundry) pressed or ....(Finished in) time selected? . Washing machine door closed? Detergent solution is not emptied. . (Rinse hold = no final spin) selected? a page 3, 4. . Clean the detergent solution pump a page 11. . Clean drain pipe and/or drain hose. Water not visible in the drum. . Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. . Not a fault -imbalance monitoring system has cancelled spinning, due to uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . S (Easy-Iron) selected? a page 5. . Too low a speed selected? a Page 5. The programme duration changes during the wash cycle. . Not a fault -the programme cycle is optimised for the particular washing process. That can lead to alterations in the programme duration in the display panel. Repeated spin start-up. . Not a fault -imbalance system is equalising the imbalance. Residual water in the compartment 0 for care products. . Not a fault -the action of the care product is not affected. . Clean the insert if necessary a page 10. Odour formation in the washing machine. . Run the ..F Cottons 90 °C programme without any laundry in the machine. Use standard detergent for this purpose. 1 status indicator flashes. Detergent may escape from the detergent drawer . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not for outdoor or down fabrics). . Reduce the detergent dosage for the next wash cycle. Pronounced generation of noise, vibration and "wandering" during spinning. . Are the appliance feet fixed? Secure appliance feet a Installation instructions. . Transportation safety devices removed? Remove transportation safety devices a Installation instructions. Noises during spinning and emptying. . Clean the detergent solution pump ..page 11. Display panel/indicator lamps do not function during operation. . Power cut? . Circuit breakers tripped? Switch circuit breakers back on or replace. . Energy saving mode active? . If the fault recurs, call our after-sales service. Programme cycle longer than usual. . Not a fault -the imbalance monitoring sys...