Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
the door). Remove the transport braces and cross connectors and store in a safe place. In addition to the instructions provided in this document, special regulations from the relevant water and electricity utility companies may apply. If in doubt, have a technician connect the appliance. Number Description 4 Covers for openings left after removing the transport safety bolts 1 Key for removing the transport safety bolts and setting the feet 1 24-40 mm dia. hose clamp for connection to a siphon 1 Door moulding 2 Door hinges with screws 1 Screw with washer for decorative door On the back of the washing machine/drum: – Water drain hose – Water supply hose – Mains cable with plug – Instruction manual and booklet containing after-sales service addresses Moisture may remain in the drum following the final inspection that every washing machine undergoes before leaving the factory. Removing the transport safety bolts Unscrew all four screws using the key provided. Remove all transport safety bolts completely and take the mains cable out of the retainers. Insert the protective covers. – Before using the appliance for the first time, ensure that all transport safety bolts have been removed and kept safe for any subsequent transport. – If you need to transport the appliance at a later date: Always reaffix the transport safety bolts to prevent damage to the washing machine. – Appliance stability is essential to ensure that the washing machine Positioning and does not “creep” during spin cycles. levelling – The installation area must be firm, clean and level. – Parquet floors and soft floor coverings, e.g. carpets or foam-backed floor coverings, are unsuitable. Intense noise, vibrations and “wandering” may be the result of incorrect Levelling levelling. – All four appliance feet must stand firmly on the ground. – The washing machine must not wobble. – Check the alignment of the washing machine with a spirit level and adjust if necessary.. – The washing machine must not rest against the side panels of the installation recess. – The lock nuts of the front appliance feet must be screwed tightly against the housing. . 25 Dimensions Width x depth x height 596 mm x 585 mm x 818 mm Weight 76 kg Hose and cable lengths Left-hand connection or Right-hand connection Water connection – To prevent leaks or water damage, you must observe the instructions in this section. – Caution: Only operate the washing machine using cold drinking water. – Do not connect to the mixer tap of an unpressurised hot-water boiler. – If in doubt, have a technician connect the appliance. – Do not use a used inlet hose. Only use the inlet hose supplied or one that was purchased from an authorised specialist retailer. – The water supply and drain hoses can be routed to the left or right, depending on installation conditions. Water supply Water drainage Drainage into a siphon Electrical connection Do not allow the water supply hose to be: – bent, squashed, modified or cut through (otherwise its strength is no longer guaranteed). Note the water pressure in the mains supply: – The water pressure should be between 50-900 kPa (0.5-9 bar) (at least 8 litres of water flow out per minute when the tap is turned on). – If the water pressure is higher than this, a pressure reducing valve must be installed. Connect the supply hose to the cold water tap with ." connection. Only tighten the screw connections by hand. Do not remove the filter from the supply hose. After connecting the water supply hose: – Open the water tap carefully, checking the leak tightness of the connection points. – Caution: The screw connection is under mains water pressure. – Do not kink the drain hose or pull it lengthways. – Height difference between the installation surface and the drain: max. 90 cm, min. 50 cm. Secure the connection point with a 24-40 mm hose clamp. The washing machine must only be connected to an alternating current using a properly installed earthed socket. Only use earth-leakage circuit breakers with the following symbol: The power supply and voltage information indicated on the washing machine (rating plate) must be the same. The connected load and fuse required are specified on the rating plate. Make sure that: – the mains plug fits the socket. – the cable cross-section is adequate. – the earthing system is properly installed. – the appliance is not standing on the mains cable. – the mains plug is accessible at all times. Changes to the mains cable may only be carried out by a qualified electrician. Do not use multiple plugs/adapters or extension cables. Mains plug: – do not plug in or unplug the mains plug when your hands are wet. – pull the appliance plug out of the socket at the plug only, not by the cable. – never unplug the plug during operation. Once the washing machine has been installed in a kitchen unit, it can be Fitting the door hinges concealed using a door. If you wish to do this, you must fit the supplied hinges to the washing machine. to the washing machine...