Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Remove the sealing cap, allow the detergent solution to flow out. Replace the sealing cap and place the For models without a drainage hose: Carefully unscrew the pump cover until the detergent solution begins to flow out. When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. Carefully unscrew the pump cover (residual water). Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). Replace the pump cover and screw it tightly. Place the service flap back on and close. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the Empty ..programme. Drainage hose at the siphon Turn the programme selector to .. (Off) and disconnect the mains plug. Loosen the hose clamp, carefully remove the drainage hose (residual water). Clean the drainage hose and siphon connecting piece. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock! Do not immerse the HydroSafe Reduce the water pressure in the supply hose: Turn off the tap. Select any programme (apart from Spin Choose Start/Reload ... Let the programme run for approximately 40 seconds. Turn the programme selector to .. (Off). Disconnect the mains plug. Clean the filter: Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter with pliers and clean. Connect the hose and check for leaks. safety device in water (contains an electric valve). Information on the display panel depending on model / Empty ..). F: 16 F: 17 F: 18 F: 21 F: 23 10 Close the washing machine door properly; laundry may be caught. Open the tap completely, supClean the filter –> page 10, Wply hose kinked or trapped; ater pressure too low. Detergent solution pump bloc/ waste pipe blocked; Clean tked; Clean the detergent solution pump -> page 10. Drainage hose he drainage hose at the siphon -> page 10. Motor fault. Call customer services. Water in the base tub, appliance leaking. Call customer services. 9 What to do if ... . Water is leaking out. – Attach/repl– Tighten the ace the drainage hose correctly. screw connection of the supply hose. . No water supply. Detergent not dispensed. – Start/Reloa– Tap not tur– Filter block– Supply hosd not selected? ned on? ed? Clean the filter -> page 10. e kinked or trapped? . Washing machine door cannot be opened. – Safety func– ....(without f– Can be option active. Programme stopped? -> page 4. inal spin) selected? -> page 3, 4. ened by emergency release only?-> page 9. . Programme does not start. – Start/Reloa– Washing m– Childproof d or (Finished in) time selected? achine door closed? lock active? Deactivate -> page 5. . Detergent solution is not drained. – ....(without f– Clean the d– Clean the winal spin) selected? -> page 3, 4. etergent solution pump -> page 10. aste pipe and/or drainage hose. . Water not visible in the drum. – Not a fault -water below the visible area. . Spin result not satisfactory. – Distribute l– (Easy-ir– Selected sarge and small items of laundry evenly in the drum. on) selected? –> page 5. peed too low? –> page 5. . Spin cycle performed several times. – Not a fault imbalance. -unbalanced load detection system adjusts the . Residual water in the compartment for care products. – Not a fault – Clean the i-the action of the care product is not affected. nsert if necessary -> page 9. . Odour formation in the washing machine. – Run prograstandard dmme Cottons 90 °C without laundry. Use etergent. . Status display... flashing. Appliance has detected a detergent overload. – Too much If foam is eMix 1 tableinto compa– Reduce the detergent used? scaping from the detergent drawer: spoon of fabric softener with . litre of water and pour rtment II (not with outdoor or down fabrics). detergent dosage for the next wash cycle. . Intense noise formation, vibrations and “wandering” during the spin cycle. – Are the appSecure the – TransportatRemove thinstructionsliance feet fixed? appliance feet –> Installation instructions. ion safety devices removed? e transportation safety devices –> Installation . . Display panel/indicator lamps do not function during operation. – Power cut? – Fuses trigg– If the fault oered? Reset/change the fuse. ccurs repeatedly, call customer services. . Programme sequence longer than usual. – Not a fault imbalance – Not a fault rinse cycle. -unbalanced load detection system adjusts by repeatedly distributing the laundry. -foam detection system active -adds an additional . Detergent residues on the laundry. – Occasionalresidues. – Use the Rinly, phosphate-free detergents contain water-insoluble se 2 cycle or brush out the laundry after washing. If you cannot correct a fault y...
Este manual também é adequado para os modelos :Máquinas de lavar - WM12E47XME/04 (1.73 mb)
Máquinas de lavar - WM12E47XME/22 (1.73 mb)