Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Filter in the water supply Risk of electric shock! Do not immerse the HydroSafe safety device in water (contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (apart from .. Spin / ....Empty). 3. Choose ....(Start/Reload). Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance, Remove the filter with pliers and clean. 2. Connect the hose and check for leaks. – Risk of scalding. Allow the detergent solution to cool down. 11 What to do if ... ..Water is leaking out. – Attach/replace the drainage hose correctly. – Tighten the screw connection of the supply hose. ..No water supply. Detergent not dispensed. – ....(Start/Reload) not selected? – Tap not turned on? – Filter blocked? Clean the filter ..page 10. – Supply hose kinked or trapped? ..Washing machine door cannot be opened. – Safety function active. Programme stopped? ..page 4. – ....(without final spin) selected? ..page 3, 4. – Can be opened by emergency release only?..page 9. ..Programme does not start. – ....(Start/Reload) or ....(Finished in) time selected? – Washing machine door closed? – Childproof lock active? Deactivate ..page 5. ..Detergent solution is not drained. – ....(without final spin) selected?..page 3, 4. – Clean the detergent solution pump ..page 10. – Clean the waste pipe and/or drainage hose. ..Water not visible in the drum. – Not a fault -water below the visible area. ..Unsatisfactory spin result. Laundry wet/too damp. – Not a fault -the unbalanced-load detection system has cancelled the spin cycle because of uneven distribution of the laundry. Distribute small and large items of laundry evenly inside the drum. – ..(Easy-Iron) selected? ..page 5. – Selected speed too low? ..page 5. ..The programme duration changes during the wash cycle. – Not a fault – the programme sequence is optimised for the particular wash process. This may result in changes to the programme duration in the display field. ..Spin cycle performed several times. – Not a fault -unbalanced load detection system adjusts the imbalance. ..Residual water in the compartment for care products. – Not a fault -the action of the care product is not affected. – Clean the insert if necessary ..page 9. ..Odour formation in the washing machine. – Run programme ..Cottons 90 °C without laundry. Use standard detergent. ..Status display....flashes. Foam may be coming out of the detergent drawer. – Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into dispenser II (not for outdoor and down-filled textiles!). – Reduce the detergent dosage for the next wash cycle. ..Intense noise formation, vibrations and “wandering” during the spin cycle. – Are the appliance feet fixed? Secure the appliance feet ..Installation instructions. – Transportation safety devices removed? Remove the transportation safety devices ..Installation instructions. ..Noises during spin and drain cycles. – Clean detergent-solution pump ..page 10. ..Display panel/indicator lamps do not function during operation. – Power cut? – Fuses triggered? Reset/change the fuse. – If the fault occurs repeatedly, call customer services. ..Programme sequence longer than usual. – Not a fault -unbalanced load detection system adjusts imbalance by repeatedly distributing the laundry. – Not a fault -foam detection system active -adds an additional rinse cycle. ..Detergent residues on the laundry. – Occasionally, phosphate-free detergents contain water-insoluble residues. – Use the ..Rinse cycle or brush out the laundry after washing. If you cannot correct a fault yourself (switching on/off) or a repair is required: – Turn the programme selector to Off and remove the mains plug from the socket. – Turn off the water supply and call customer services ..Installation instructions. Instruction manual Washing machine Observe the safety instructions on page 8. en Read these instructions and the separate installation instructions before operating the washing machine. 11What to do if ... ..Water is leaking out. – Attach/replace the drainage hose correctly. – Tighten the screw connection of the supply hose. ..No water supply. Detergent not dispensed. – ....(Start/Reload) not selected? – Tap not turned on? – Filter blocked? Clean the filter ..page 10. – Supply hose kinked or trapped? ..Washing machine door cannot be opened. – Safety function active. Programme stopped? ..page 4. – ....(without final spin) selected? ..page 3, 4. – Can be opened by emergency release only?..page 9. ..Programme does not start. – ....(Start/Reload) or ....(Finished in) time selected? – Washing machine door closed? – Childproof lock active? Deactivate ..page 5. ..Detergent solution is not drained. – ....(witho...