Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
pleased to find that it washes, rinses and spins without you having to handle the ;, clothes in between times. You will obviously want to obtain the best possible wash. By reading and following the Instructions in this booklet you will achieve excellent results. Please:ensure that the Installation Instructions have been carried out. If you should need any further advice or assistance please contact the Bendix agent from whom your machine was purchased or your nearest Tricity Bendix Customer Service Centre, listed in the yellow pages under ‘Domestic Appliances’. 1 C k' k Model 7 12158 Autowiiuher electronic 1000 Height, overall (H) 850 mm 33 Vi. in Electrical loadings Width (W) 595 mm 23 Vi in Heater Depth • door closed (D) 570 mm 22 V? in Motor - tumble • door open (d) 960 mm 37-'/., in - spin Height, to services (HS) 765 mm 30 in Rear projection (C) 50 mm 2 in Weigh! - empty 87kg 1921b Drain Pump 2.5 kW 250W 300W& 550W 95W 2 Si* , SITE REQUIREMENTS I A firm, level, and a relatively smooth floor, with :; 1 the services brought to the appliance. A minimum of 12 mm (Vi In) clearance Is required each side of the appliance to permit removal for servicing. UNPACKING flrlMSlAI i v\ ter' Remove the prolectlve packing and polystyrene base. Remove! back panel screws and lift panel clear. Using the spanner provided, remove the four integral transit straps as shown in the diagram below, together with the three chassis bracing straps and store in a convenient place together with the fixing bolts and washers. Insert the four plastic plugs provided into the (our bolt holes vacated by the transit fixing bolts in the back panel. Relocate and fix the back panel. Always refit the transit straps before transporting the appliance. Connect the hoses, making sure that the sealing washers 'x' are in place. Note. Some hoses now incorporate the sealing washers 'x' into the connectors Lay machine on its back on polystrene corner pieces. Remove polystyrene base by pulling off. Do not lay machine on its side. 3 Mains lead: 3 core 2.7 m 9 ft Fused and earthed supply: 240V 50Hz a.c. Fuse ratings: 13A ,i .u ,i) ¡lil'.st'HLIAWCF. IWUSI BEEAHTHED If this appliance is fitted with a non-rewireable plug for which your socket is unsuitable then it should be cut off and an appropriate plug fitted. The removed plug should be disposed of as Insertion of the plug into a 13 A socket is likely to cause an electrical hazard. If It Is necessary to change the fuse in a non-rewireable plug the fuse cover must be refitted. If the fuse cover is lost or damaged the plug must not be used until a replacement is obtained. Replacement fuse covers are available from Trlclty Bendlx Customer Parts Centre, PO Box 14, Newton Aycliffe. PL5 6XA. It is important that the colour of the replacement fuse cover corresponds with the colour marking on the base of the plug. I,.. . Thewiresinthemainsleadarecolouredinaccordancewiththefollowingcode: GREEN AND YELLOW EARTH 7 BLUE NEUTRAL BROWN LIVE As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green and yellow must be connected to the terminal which is marked with the letter ‘E’ or by the 'Earth' symbol or coloured green or coloured green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter 'N' or colour black. The wire which is coloured brown must be connected to the terminal which Is marked with the letter 'L' or coloured red. The appliance must be protected by a 13 A ASTA approved (BS 1362) fuse if a 13 A (BS 1363) plug or a non-rewireable plug is used or if any other type of plug Is used by a 15 A fuse either in the plug or adapator or at the distribution baord. K ,ir;, Supply: Hot & Cold, or Cold-only, using 'F' connector 25115. Pressure -minimum 25kN/m2 3.5 ltp/in2 -maximum 1000kN/m2 140 lb/in2 Temperature: Hot water 60°C maximum Inlet connection % BSP 3ABSP Inlet hose length 1.35 m 53 in Inlet height HS2 0.3 m 10 ft Preferred stopcock position: at side of machine 300 mm 1 ft Stopcock recommended: Bendix 24041 hot & 24042 cold ., :: I.' i1 * il.. I.