Assessments - 5, GPA: 3.8
(
)
)
|
Facilidade de uso
BROW. LIVE (L. GREEN & YELLOW EARTH (E. Disposing of the appliance. When disposing of the applianc. please remove the plug b. cutting the mains cable as clos. as possible to the plug body an. dispose of it as described above. GREEN & YELLOW 13 ampere fuse BROWN CROSS-BAR CORD GRIP BLUE . ARGHERIT. Margherita - Iinstructions for installation and us. 1. . ARGHERIT. Instructions for the fitte. Mounting the woode. panel onto the door an. inserting the machin. into cabinets. In the case where the machin. must be shipped for fina. installation after the woode. panel has been mounted, w. suggest leaving it in its origina. packaging. The packaging wa. designed to make it possible t. mount the wooden panel ont. the machine without removing i. completely (see figures below). The wooden panel that cover. the face of the machine must no. be less than 18 mm in thicknes. and can be hinged on either th. right or left. For the sake o. practicality when using th. machine, we recommend that th. panel be hinged on the same sid. as the door for the machine itsel. - the left. Door Mounting Accessorie. (Fig. 1-2-3-4-5. N° 2 Hinge Supports Fig. . Fig. . N° 2 Hinges 1 2 3 4 5 6 lavabiancheriawashing machinemachine laverwaschmaschine Lato portaDoor side Cote porte Tur seite Fig. . B A N° 1 Magnet Fig. . D - No. 6 type A self-threadin. screws, l =13 mm. C - No. 2 type B metric. countersunk screws, l =25; fo. fastening the magnet plate to th. cabinet. E 2 3 4 5 6 lavabiancheria washing machine machine laverwaschmaschine Lato portaDoor sideCote porter s - No. 4 type C metric screws. l =15 mm; for mounting the hing. supports to the cabinet. - No. 4 type D metric screws. l =7 mm; for mounting the hinge. on the supports. N° 1 Rubber plug N° 1 Magnet plate Fig. . N° 1 Spacer Fig. 4/. 1. Margherita - Instructions for installation and us. Mounting the Parts ont. the Face of the Machin. - Mount the hinge supports ont. the face of the machine. positioning the hole indicated b. the arrow in fig. 1 towards th. inside of the face and using th. type C screws. - Mount the magnetic plate o. the opposite side, at the top. using the two type B screws. - Place the spacer illustrated i. fig. 4/B between the applianc. front and the magnet receiver. Using the Drillin. Templat. - To trace the positions of th. holes on the left-hand side of th. panel, align the drilling templat. to the top left side of the pane. using the lines traced on th. extremities as a reference. 570min 815 540 595 820 . 900 600 min Fig. . - To trace the positions of th. holes on the right-hand side o. the panel, align the drillin. template to the top right side o. the panel. - Use an appropriately sized route. to mill the holes for the tw. hinges, the rubber plug and th. magnet. Mounding the Parts ont. the Wooden Panel (Door. - Insert the hinges into the hole. (the movable part of the hing. must be positioned facing awa. from the panel) and fasten the. with the 4 type A screws. - Insert the magnet into the to. hole on the opposite side of th. hinges and fasten it with the tw. type B screws. - Insert the rubber plug into th. bottom hole. The panel is now ready to b. mounted onto the machine. D C C Fig. . Mounting the Panel int. the machin. Insert the nib of the hing. (indicated by the arrow in fig. 2. into the hole for the hinge an. push the panel towards the fron. of the machine. Fasten the tw. hinges with the type D screws. Fastening the plint. guid. If the machine is installed at th. end of a set of modular cabinets. mount either one or both of th. guides for the base molding (a. shown in fig. 8). Adjust them fo. depth based on the position o. the base molding, and, i. necessary, fasten the base to th. guides (fig. 9). This is how to assemble th. plinth guide (fig.8). Fig. 8 . ARGHERIT. Fasten angle P using screw R. insert plinth guide Q into th. special slot and once it is in th. desired position, lock it in plac. using angle P and screw R. Inserting the machin. into the Cabine. - Push the machine into th. opening, aligning it with th. cabinets (fig. 6). - Regulate the adjustable feet t. raise the machine to th. appropriate height. - To adjust the position of th. wooden panel in both the vertica. and horizontal directions, use th. C and D screws, as shown in fig. 7. Important: close the lower part o. the appliance front by ensurin. that the plinth rests against th. floor. Fig. . Accessories provided fo. the height adjustmen. The following can be found insid. the polystyrene lid (fig. 10). 2 crossbars (G). 1 strip (M. Fig. 10 the following can be found insid. the appliance drum. 4 additional feet (H). 4 screws (I). 4 screws (R). 4 nuts (L). 2 plinth guides (Q. Adjusting the applianc. heigh. The height of the appliance ca. be adjusted (from 815 mm t. 835 mm), by turning the 4 feet. Should you require the applianc. to be placed higher than th. above height, you need to use th. following accessories to raise i. to up to 870 mm. - the two crossbars (G. - the 4 feet (H. - the 4 screws ...