Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury, death and/or property damage! Retain instructions for future reference. Framing Nailer Note: This framing nailer is shipped with the BLACK single cycle mode trigger installed. Always know the operational mode of the nailer before using. Failure to know the operational mode could result in death or serious personal injury. Operational Modes This stick framing nailer may be operated in the “Single Cycle” or the “Bottom Trip” mode. The nailer is delivered in the single cycle mode. A separate ‘red’ trigger for “Bottom Trip” mode is included with tool as an accessory. SINGLE CYCLE MODE When the black trigger is installed, nailer is in single cycle mode. This method is recommended when precise nail placement is required. Operation in this mode requires trigger to be pulled each time a nail is driven. Nailer can be actuated by depressing the Work Contact Element (WCE) against work surface followed by pulling the trigger. The trigger must be released after each fastener is driven to allow tool to reset. Since the tool can only be actuated by first removing the finger from the trigger, this is considered to be a more restrictive mode of operation, suitable for less experienced users. BOTTOM TRIP MODE When the red trigger is installed, the nailer is in bottom trip mode. This method is recommended when less precise nail placement is required. Operation in this mode requires trigger to be depressed with nailer off of the work surface. Then, the nose of the nailer is tapped against the work surface causing a nail to be driven. Each time the Work Contact Element is depressed, a nail is driven into the work surface. Extreme care should be taken because a nail will be driven when the WCE is pressed against any surface. Since the tool can be actuated without removing the finger from the trigger, this is considered to be a less restrictive mode, suitable for more experienced users. MODE CONVERSION To convert the tool from one mode to the other: 1. Remove o-ring on the side of trigger pin. 2. Remove trigger pin, trigger, and trigger spring (if included). 3. Switch out only the trigger. 4. Replace trigger spring (if included), trigger, trigger pin, and o-ring. Do not attempt to modify the trigger components in any manner and do not attempt to use any other trigger components other than those intended for this tool. See the tool manual for further Safety and Operation information. Contact your Campbell Hausfeld representative if you have any questions. Mode Conversion Trigger spring (if included) O-ring Trigger pin Trigger This tool meets or exceeds Industries’ Standards as set forth by the American National Standard IN724600AV 12/07Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002. © 2007 Feuillet D’Instructions Modeles NS3490, NS2891 et NS2190 S’il vous plait lire et conserver ces instructions. Lire attentivement avant de monter, installer, utiliser ou de proceder a l’entretien du produit decrit. Se proteger ainsi que les autres en observant toutes les instructions de securite, sinon, il y a risque de blessure et/ou degats materiels! Conserver ces instructions comme reference. Cloueuse a Charpente Note: Cette cloueuse d’encadrement est expediee avec la gachette en mode de cycle unique NOIRE installee. Toujours connaitre le mode de fonctionnement de la cloueuse avant de l’utiliser. Manque de se familiariser avec le mode de fonctionnement peut resulter en mortalite ou en blessures personnelles serieuses. Modes De Fonctionnement Les cloueuses pour charpentes peuvent fonctionner dans le mode “Cycle Unique” ou “Declenchement Du Bas”. La cloueuse est livree dans le mode cycle unique. Une gachette ‘rouge’ distincte pour le mode ‘Declenchement du bas’ est incluse avec l’outil comme accessoire. MODE A CYCLE UNIQUE Lorsque la gachette noire est installee, la cloueuse est dans le mode cycle unique. Cette methode est recommandee lorsque le placement pecis du clous est requis. Le fonctionnement dans ce mode necessite que la gachette soit tiree chaque fois qu’un clou soit enfonce. La cloueuse peut etre actionnee en appuyant le mecanisme de declenchement par contact (WCE) contre la surface de travaille et ensuite en tirant sur la gachette. La gachette doit etre relachee apres l’enfoncement de chaque attache pour le permettre de se reenclencher. Puisque l’outil peut etre active seulement en retirant d’abord le doigt de la gachette, ceci est considere un mode plus restrictif et plus ...