Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
1 -6 Model W1783 (Mfg. Since 2/07) OPERATIONS Loading When replacing nails in your Model W1783, follow these guidelines: Nails.................... L-Shaped Cleat Nails Length: .................................... 1"–2" Capacity: ................................... 100 Note: Use 11.2" nails to install 1.2" flooring, and 2" nails to install 3.4" flooring. To load your nailer, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Slide a strip of nails, pointed-end down, into the rear of the magazine, as shown in Figure 2. Figure 2. Loading nails into the nailer. 3. Press the button inside the pusher (see inset photo, Figure 2), pull the pusher all the way back, then allow the pusher to slide forward against the nail strip. Operating If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. The Model W1783 comes with two base plates: — The thinner base plate is for use with 3.4" flooring. — The thicker base plate is for use 1.2" flooring. To operate your nailer, do these steps: 1. Install the correct base plate for your size of flooring material. 2. Place the flooring nailer on the floor with the nail discharge facing down, then connect the air supply. Always point the nailer at the ground when connecting to the air supply. DO NOT aim it in the direction of another person or yourself. Failure to heed this warning could result in serious personal injury. 3. Position a flooring strip and tap it into place with the metal side of the included hammer. -7 Model W1783 (Mfg. Since 2/07) NOTICEDO NOT use the nailer to position the flooring strip. Doing so will damage the nailer and possibly the flooring strip. Note: If you are using pre-finished flooring material, test the nailer on a sample strip. If the nailer base plate is damaging or marring the flooring surface, replace it with a new one. 4. Place the nailer on the flooring strip, as shown in Figure 3. Figure 3. Positioning nailer on flooring strip and operating. DO NOT place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 5. Make sure the cleat on the nailer base plate is lined up with the edge of the groove on the flooring strip. 6. Using the rubber end of the included hammer, hit the whack cap of the nailer ONCE with a light to medium force to shoot a nail into the wood. Never hit the whack cap of the nailer multiple times to drive the nail into the wood. If necessary, use a hammer and nail punch to drive the nail in. Failure to heed this warning could cause a nail jam or a ricochet, and serious personal injury. 7. Check the nail for satisfactory penetration. — If the nail depth is satisfactory, proceed with your project. — If the nail depth is too shallow, slightly increase the air pressure. — If the nail depth is too deep, slightly decrease the air pressure. Note: Nailing penetration is not always consistent due to variations in the flooring material. If necessary, use a hammer and nail punch to finish seating the nail. Clearing Jammed Nails A jammed nail must be cleared before using the nailer again. To clear a jammed nail from the discharge area, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Pull the magazine pusher all the way back and remove the nail stick. -8 Model W1783 (Mfg. Since 2/07) 3. The jammed nail should be visible in the discharge area. — If the jammed nail can be removed with needle nose pliers, do so and continue to Step 7. — If you cannot remove the jammed nail, then continue with Step 4. 4. Use the 4mm hex wrench and remove the four cap screws and lock washers that secure the magazine to the nailer (see Figure 4). Note: It may be necessary to remove the base plate to pull the magazine out. Figure 4. Location of cap screws securing the magazine to the nailer. 5. Remove the jammed nail from inside the discharge area with a pair of need nose pliers (see Figure 5). Figure 5. Jammed nail in discharge area. 6.Re-install the magazine. 7. Throw the damaged nail away and insert a new nail stick that only contains clean, undamaged nails. DO NOT use dirty or damaged nails! Replacing Pistons/ O-Rings Under heavy use, the piston or O-rings may wear out. Replacement is quick and easy. Contact your authorized Shop Fox dealer to obtain the Piston Repair Kit (Part Number X1783068) or Complete O- Ring Kit (Part Number X1783070). To replace the piston and O-rings, do these steps: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Remove all the nails from the magazine. 3. Use the 4mm hex wrench and remove the four cap screws and lock washers that secure the magazine to the nailer (see Figure 4). Note: It may be necessary to remove the base plate to pull the magazine out. Always disconnect nailer from air whenever servicing! During main- tenance, a nailer connected to air ma...