Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
— If the nailer does fire when the trigger is pulled, without the safety nose mechanism being depressed, immediately disconnect the nailer from the air supply and call Grizzly Technical Support at (570) 5469663 for help. -7 OPERATIONS 3. Lift the pusher upward toward the nailer Loading body until the pusher latches into the lock notch as shown in Figure 4. Use nails meeting the specifications listed for your nailer on Page 4 of this manual. Figure 3. Sliding the pusher to the rear of the magazine. pusher into the lock notch. locked at the rear of a strip of nails into shown in Figure 5. nail strip into the magazine. 2. Pusher Lock Notch 5.Lift the pusher out of the lock notch and guide it forward to push the nail strip to the nose of the nailer. (Do not let it snap.) Pusher Nail Strip -8- H7945/H7946/H7995 26° Angle Nailer Unloading Nails To remove unused nails: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Point the nailer away from you and all bystanders. 3. Slide the pusher to the rear of the magazine and latch it into the lock notch. 4. Move the nails to the rear of the magazine and remove them by hand. Rotating the Exhaust Cover The exhaust cover rotates as needed to direct the exhaust away from you. To rotate the exhaust cover: 1. Use the 4mm hex wrench to loosen the exhaust cover cap screw as shown in Figure 6. Exhaust Cap Screw Figure 6.Loosening the exhaust cap screw. 2. Rotate the exhaust cover by hand to aim the exhaust port in the desired direction. 3. Tighten the exhaust cover cap screw. H7945/H7946/H7995 26° Angle Nailer -9 -10- H7945/H7946/H7995 26° Angle Nailer Using the Nailer Before you operate your nailer, place five to six drops of air tool oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer: 1. Connect the air supply to the quick connect fitting on your nailer. 2. To test for proper nail penetration, hold the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded. 3. Depress the safety nose mechanism against your workpiece. Note: Deflection is caused when grain irregularities, knots or foreign objects inside the wood cause the nail to change its path, resulting in the nail puncturing the surface of the workpiece. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. 5. Pull the trigger. — If the nail penetrates the wood to the depth you want, continue with your intended operations. — If the nail either went too far or not far enough, adjust the depth of fire by following the procedures listed on Page 11. 4. Before pulling the trigger, make sure your free hand and other body parts are positioned out of the way of a potential path of a nail in case of deflection (illustrated below in Figure 7). Figure 7. Example of nail deflection. Read the manual before operation. Become familiar with these nailers, their safety instructions, and operation before beginning any work. Serious personal injury may result if safety or operational information is not understood or followed. Adjusting Depth Adjusting the depth of nail penetration is done by turning the adjustment knob located near the trigger as shown in Figure 8. Depth Adjustment Knob Figure 8.Depth adjustment knob. To adjust the nail depth: 1. DISCONNECT NAILER FROM THE AIR SUPPLY AND POINT THE NAILER IN A SAFE DIRECTION! 2. Turn the depth adjustment knob to increase or decrease nail penetration: — If you want to increase the nail depth, then turn the adjusting knob counter clockwise. — If you want to decrease the nail depth, then turn the adjusting knob clockwise. 3. Connect the nailer to the air supply, test the nail depth, and repeat this entire procedure if necessary until the nail depth is satisfactory. Clearing Jammed Nails A jammed nail must be cleared before the nailer is used again. To clear a jammed nail from the discharge area: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Remove all nails from the magazine. (See Unloading Nails on Page 9.) 3. Use a pair of pliers to grab the jammed nail and pull it from the nose as shown in Figure 9. Jammed Nail Figure 9.Using pliers to remove a jammed nail. Note: If you cannot remove the jammed nail in this way, then disassemble the nailer's nose assembly to gain full access to the nail, remove it and reassemble. Refer to the parts breakdown drawing included in the back pages of this manual for guidance during this procedure. 4. Throw the damaged nail away and insert a new strip of nails. DO NOT use dirty or damaged nails! H7945/H7946/H7995 26° Angle Nailer -11 Replacing Pistons/O-Rings If you need to replace piston parts in your nailer, you can purchase a piston repair kit from Grizzly: call 1-800-523-4777. The Piston Repair Kit part number for Model H7945 is PH7945090; the Piston Repair Kit part number for Model H7946 is PH7946090; the Piston Repair Kit part number for Model H7995 is H7...