Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Typical filter/lubricator/regulator installation order. H6141 Air Palm Nailer -7 OPERATIONS General Operations If you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. To operate your nailer: 1. Connect the air supply to the quick connect fitting. 2. Hold the nail firmly in place with one hand as if using a regular hammer. 3. Make sure you are positioned out of the way of a potential path of a nail in case of deflection. Deflection is caused when grain irregularities, knots or foreign objects inside the wood cause the nail to change its path, resulting in the nail puncturing the surface of the workpiece, as shown in Figure 3. Figure 3.Example of nail deflection. -8 4. Place the tip of the palm nailer over the end of the nail. When the ram pin touches the nail head, it will automatically begin to hammer the nail into the workpiece. Hold the nailer in place until the sliding depth guide is fully depressed. 5. You can stop the nailer at any time by simply lifting it away from the nail and workpiece. This is useful if you do not wish for the nail to be countersunk into the workpiece. 5. When the nail is fully hammered into the workpiece, the nailer will automatically stop. Note: The air palm nailer will automatically countersink all nails to a depth of around 2mm or 5.64". Operation of this nailer has the potential to propel debris into the air which can cause eye injury. Always wear ANSI-approved safety glasses or goggles when operating equipment. H6141 Air Palm Nailer Replacing Pistons/O- Rings If you use your nailer day in and day out, replacement pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. Always disconnect air from nailer whenever servicing! During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury! To replace a piston: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Unscrew the nose piece with a 19mm wrench. 3. Remove the nose piece, depth guide, compression spring and flat washer. 4. Remove the four cap screws and washers on the back of the nailer. 5. Remove the cap. 6. Push the ram pin towards the inside of the nailer. This will push the cylinder free of the housing. 7. Remove the piston from the cylinder by pulling it free by the ram pin. 8. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 9. Insert the new piston in the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston inside the cylinder. 10. After the piston is inserted correctly, place the cylinder back in the housing. If seated correctly, the cylinder will snap into place. 11. Push the cylinder collar down into the housing as far as it will go. The horizontal air slots on the side of the cylinder should be visible. 12. Replace the rear cap assembly and tighten the four cap screws. 13. Replace the flat washer, compression spring, depth guide and nose piece and tighten using a 19mm wrench. 14. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. H6141 Air Palm Nailer -9 CLEANING & LUBRICATION Cleaning Use a good solvent to clean the nose piece and depth guide of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. Never use gasoline or other flammable liquids to clean this tool. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Lubricating Special oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 4) before every use, or after 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace with Grizzly Model G2820 Pneumatic Tool Oil. Another option to manual oiling would be to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular manual lubrication of your nailer will not be necessary. Just make sure there is always oil in the lubricator. Figure 4. Lubricating nailer via air inlet. -10-H6141 Air Palm Nailer H6141 PARTS BREAKDOWN ................................................................................ REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB15M CAP SCREW M5-.8 X 20 2 PH6141002 CAP 3 PH6141003 O-R...