Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
150 pSI mAX AIr preSSure! exceeding this pSI may result in injury/tool damage.. Specifications Air Inlet....................................................1.4" NPT Average Air Consumption ........................ 4 CFM Operating Pressure .................................. 90 PSI Capacity................... 14 oz., (400cc bulk grease) Weight ........................................3.2 lbs. (Empty) Inventory (Figure 1) Qty A.. Grease Gun ............................................... 1 B.. Hydraulic Coupler with Extension .............. 1 Operation To improve tool lifespan, use a filter/lubricator/ regulator setup, as shown in Figure 2. Otherwise, lubricate multiple times daily with 2–3 drops of pneumatic tool oil. Place the oil directly into the air fitting, as shown in Figure 3. Hydraulic Coupler Extension Head Assembly Cartridge Body Figure 1.. Model H0580. Quick Connector Quick Coupler Air Hose Quick Coupler Quick Connector Lubricator Filter Regulator Air Compressor Your Tool Figure 2.. Installing a filter/lubricator/regulator to improve the lifespan of your tool. Figure 3.. Lubricating directly into air fitting. If you need help with your new pneumatic tool, call our Tech Support at: (570) 546-9663. COPyrIGHT © MAy, 2008 By GrIzzLy INduSTrIAL, INC. WArnIng: nO pOrtIOn OF thIS mAnuAl mAy Be reprOduced In Any ShApe Or FOrm WIthOut the WrItten ApprOvAl OF grIzzly InduStrIAl, Inc.. #jM10671 PrINTEd IN TAIWAN to operate your h0580 grease gun: 1.. Connect the grease gun to compressed air regulated at a pressure between 30 and 100 PSI. note: For quick connection type air fittings, a 1/4" NPT female plug is needed (sold separately.) 2.. Wipe all fittings clean with a shop towel. 3.. Pull grease gun trigger once or twice to purge the coupler of any contaminates or old grease. 4.. Push the grease gun coupler onto the fitting to be lubricated. note: It is easier to attach the coupler to the fitting at a slight angle. Be sure to center the coupler over the fitting when applying grease. 5.. Pull the trigger to inject grease. 6.. After lubricating, turn the coupler at a slight angle to release it from the fitting. NOTICE Some mechanical systems may only require a small amount of grease, while others require much more.. understand the lubrication requirements of the part you are lubricating.. Failure to follow this instruction can damage seals or under-lubricate parts, causing costly damage.. Installing a grease cartridge To install a grease cartridge, the follower assembly must be fully withdrawn, allowing room for the new cartridge. to properly load a new grease cartridge: 1.. dISCONNECT THE TOOL FrOM THE AIr SuPPLy! 2.. Pull the follower rod back until it is fully extended; the locking tab will automatically hold it in place (Figure 4). Follower rod Locking Tab Figure 4.. The follower rod and locking tab 3.. remove the head assembly (Figure 1) from the cartridge tube. 4.. If an empty grease cartridge is in the gun, remove it by carefully pushing the locking tab and allowing the follower rod to slowly move into the cartridge tube. 5.. After ejecting the used grease cartridge, pull the follower rod back until it is fully extended, and allow the locking tab to hold it in place (Figure 4). 6.. Insert the new greaes cartridge into the cartridge tube according to the instructions on the grease cartridge. 7.. Securely fasten the head assembly to the cartridge tube and release the follower rod by pushing on the locking tab. 8.. Push the follower rod in as far as possible. -2 H0580 Pneumatic Grease Gun Filling from a Bulk grease container 1.. dISCONNECT THE TOOL FrOM THE AIr SuPPLy! 2.. Pull the follower rod back until it is fully extended, the locking tab will automatically hold it in place (Figure 4). 3.. remove the head assembly from the cartridge tube. 4.. remove any grease from the cartridge tube by pushing the locking tab and carefully releasing the follower rod, allowing it to slowly move into the cartridge tube. 5.. Without introducing bubbles, pack grease into the head cavity and plunger assembly until they are full (Figure 5). Head Cavity Plunger Assembly Bleeder Valve Figure 5.. Grease locations and bleeder valve. 6.. Insert the open end of the cartridge tube into the barrel or drum of the bulk grease to be added. 7.. Slowly pull the follower handle back while pushing the cartridge tube deeper into the grease. This method will help prevent drawing in air bubbles. 8.. When the follower rod is fully extended, allow the locking tab to hold it in place (Figure 4). 9.. Securely fasten the head assembly to the cartridge tube and release the follower rod by pushing on the locking tab. 10.. Push the follower rod in as far as possible. Filling With a Bulk grease pump 1.. dISCONNECT THE TOOL FrOM THE AIr SuPPLy! 2.. Pull the follower rod back until it is fully extended, the locking tab will automatically hold it in place. 3.. Insert the grease gun grease inlet (part # 11) into the proper fitting on the pump operated bulk ...