Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this tool. Approved accessories are available from Harbor Freight Tools. 17. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 18. Use proper size and type air pressure line and fittings. The recommended air line for this tool is 3/8” delivering no more than 125 psi. Recommended air inlet size is 1/4” - 18 npt. 19. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. 20. Compressed air only. Never use combustible gas as a power source. [_ 21. Do not put a nail into the Air Palm Nailer until you are ready \ to work. Do not point the Air Nailer toward any person or animal. Severe injury may result in case of accidental ejection of a nail. _ 22. Disconnect air supply when done working. Before storing or making any adjustments to the Nailer make sure that the compressed air is disconnected. 23. Fire fasteners into an appropriate work surface only. Do not attempt to fire fasteners into surfaces too hard to penetrate. Do not drive fasteners on top of other fasteners, or at too steep of an angle. Fasteners can ricochet causing personal injury. Never fire the Nailer into the air, or point it toward yourself or another person. Always wear ANSI approved safety goggles during use, maintenance, and reloading. 24. Do not fire fasteners too close to the edge of a workpiece. They may split the workpiece and fly free, causing personal injury. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-based paints Crystalline silica from bricks and cement or other masonry products Arsenic and chromium from chemically treated lumber (California Health & Safety Code 25249.5, et seq.) WARNING: The Brass components of this product contain Lead, a chemical known to the state of California to cause birth defects (or other reproductive harm). (Calif. Health &Safety Code 25545.5 et.seq.) REV 11/06 SKU 93496 For technical questions please call 1-800-444-3353 Page 4 Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Air Pressure Supply This tool is designed to operate with a maximum air pressure of 125 psi. You must use an air regulator, set at 125 psi or below. Note: Performance of this tool may vary depending on variations in local air pressure. In use, this tool will use 2 - 4 Cubic Feet per Minute of compressed air at 125 psi. For satisfactory performance, you must use an air compressor capable of delivering this volume of air at the stated pressure. We recommend that you use both a filter and an in-line oiler in your air supply system as illustrated in the diagram below. These components are not included with this tool, but are available from Harbor Freight Tools. If you do not use a filter and in-line oiler, put a few drops of water displacement oil into the air line before each use. After each use, the Air Hand Nailer should be carefully drained of collected moisture and sprayed with a water displacement oil. We recommend that you install a quick-release nipple (not included) into the Air Inlet (23). Quick release connectors at all points in an air pressure system make your work easier. 1 Hose Line Air Valve Oiler Filter Air Palm y . 1 1 AIR Nailer et..............~ v m «A loi ’ To! COMPRESSOR Regulator Recommended Air Line Components Unpacking When unpacking, check to make sure the following parts are included. Air Palm Nailer Tool Leather Cover (1) 4mm Hex Key If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. REV 11/06 SKU 93496 For technical questions please call 1-800-444-3353 Page 5 Operation NOTE: This tool is assembled when you receive it, and may be used immediately. However, we recommend that you install a quick disconnect adapter (not included) to the Air Inlet (23) before use. WARNING: Do not put a nail into the Air Palm Nailer until you are ready to work. WARNING: Do not point the Air Palm Nailer toward any person or animal. Severe injury may result in case of accidental ejection of a nail. 1. Attach the air supply hose (not included) to the tool. 2. Grip the base of the tool in one hand. Note that there is a hand strap and thumb strap on the Leather Cover (25) to fa...
Este manual também é adequado para os modelos :Pistola de pregos - AIR PALM NAILER 93496 (787.53 kb)