Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). . Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. Note: Performance of this tool (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Special Warnings for this Tool It is especially important that you read and comply with the following safety precautions. 1. Never, under any circumstances, press the tip of this tool against another person or yourself. 2. Excess air may remain in the tool even after the tool is disconnected from the air supply. For this reason, be especially careful never to carry this tool with your finger on the trigger, and do not press the tip against any surface even when the tool is not connected to an air supply. 3. While using this tool, be sure to keep fingers, hands and all other body parts away from the tip of the tool. 4. Never use combustible gas as a power source. 5. Never use gasoline or other flammable liquids to clean the Stapler. 6. Do not exceed the maximum operating pressure of 95 PSI as stated in the Specifications Chart and warning label. 7. Ear protection is required for the operator and others in the work area. 8. Never attempt to drive staples on top of other staples. 9. Never attempt to keep the Trigger depressed with tape or wire. 10. Never leave the tool unattended or connected to the air supply when not in use. 11. Do not throw the tool or use it as a hammer to knock material into place. 12. Avoid prolonged use of the Stapler, and do not use this tool if you have back, neck or other bodily injuries that might be aggravated by the jerking motion of the tool. Stop using this tool if you experience pain in your arms or hands. SKU 46365 Page 4 13. Do not use this tool if it is not loaded, as this will accelerate wear on the tool. 14. Be sure all hoses and fittings are free from damage and dirt. Replace any part that does not appear to be operating properly. Warning: People with pacemakers should consult with their physician(s) before using this product; operation of equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure all parts listed on Page 7 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual. Maintenance 1. Do not store the Stapler in cold or freezing temperatures. If you are operating the Stapler in cold weather, use a permanent antifreeze as lubricant. Certain drying agents may damage o-rings and seals, so be sure to check these periodically. 2. It is recommended that you use an Oiler with this tool, especially if you use this tool regularly. Be sure the check the oil level in the Oiler before each use, and during prolonged periods of use. 3. If you are not using an Oiler, you must lubricate the Stapler before and after each use. Be sure to disconnect the tool from the air supply if you are lubricating it by hand. To lubricate this tool: add 5-6 drops of air tool lubrication to the Air Inlet. Do not use detergent oil or oil adhesives. Run the Stapler for a short time after lubrication and wipe off all excess oil. 4. A filter (not included) can be used to remove liquid and solid impurities which may rust or block internal parts and mechanisms. Periodically check the Filter and drain any water. SKU 46365 Page 5 Air Connection STAPLER Air Connection STAPLER Note: Air Compressor is not supplied. You may use Quick-Couplers and Quick-Connectors (not supplied) as shown in the diagram above. Do not connect Couplers directly to the Air Inlet. Doing so will increase the overall bulk of the tool and strain the inlet threads. 1. Read and follow all safety precautions as listed on Pages 2-5 of this manual. 2. Acquire a Union Fitting (not supplied) and screw into the Air Plug [32, see Assembly Diagram on Page 8]. Tighten with a wrench. 3. Attach a Quick-Connector (not supplied) to the Union Fitting if desired. This allows quick exchange of the Air Hose to other air tools. 4. If staples do not drive down tightly, adjust to a higher pressure setting until satisfactory. Reduce air pressure if the staples are being driven too deep. This air tool requires lubrication during operation. For best results, it is recommended to have an Oiler and Water Filter in line with the Air Supply as shown. This will extend the life of the tool. Loading the Stapler When loading, the Stapler must be disconnected from the Air Compressor Hose. 1. Only use the prope...