Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
. Always disconnect nailer from air line before clearing jams, adjusting or servicing the nailer, relocating the nailer, or when the nailer is not in use. Always reconnect the air line BEFORE loading any fasteners. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. Campbell Hausfeld Nailers meet or exceed Industries’ Standards as set forth by the American National IN715702AV 2/08Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002. © 2008 Campbell Hausfeld / Scott Fetzer For parts, product & service information visit Nailer Components And Specifications NS219001 NS219500 • REQUIRES (SCFM with 16 nails 4.1 4.1 per minute @ 90 psi) • AIR INLET 1/4” NPT 1/4” NPT • NAIL LENGTH 2” to 2” to RANGE 31.2” 31.2” • NAIL SHANK 0.113” to 0.113” to RANGE 0.131” 0.131” • MAGAZINE CAPACITY 60-75 60-75 • WEIGHT 9 lbs 3 oz 7 lbs 6 oz • LENGTH 19.25” 19.25” • HEIGHT 15.25” 15.25” • MAX. PRESSURE 120 psi 120 psi • PRESSURE RANGE 70 - 120 psi 70 - 120 psi NS319001 NS349001 4.1 1/4” NPT 2” to 31.2” 0.113” to 0.131” 75-105 9 lbs 2 oz 18.50” 15.00” 120 psi 70 - 120 psi Adjustable Direction Exhaust Deflector Trigger Nail Loading Area Magazine Warning Labels (Backside) Debris Shield Work Contact Element Nail Discharge Area Models NS219001, NS219500, NS319001 & NS349001 Operating The Nailer Read this manual and understand all safety warnings and instructions before operating the nailer. LUBRICATION This nailer requires lubrication before using the nailer for the first time and before each use. If an inline oiler is used, manual lubrication through the air inlet is not required on a daily basis. The work surface can become damaged by excessive lubrication. Proper lubrication is the owner’s responsibil- ity. Failure to lubricate the nailer properly will dramatically shorten the life of the nailer and void your warranty. 1. Disconnect the air supply from the nailer to add lubricant. 2. Turn the nailer so the air inlet is facing up. Place 4-5 drops of 30 W non- detergent oil into air inlet. Do not use detergent oils, oil additives, or air tool oils. Air tool oils contain solvents which will damage the nailer’s internal components. OIL 3. After adding oil, run nailer briefly. Wipe off any excess oil from the cap exhaust. Recommended Hookup RECOMMENDED HOOKUP 1. The air compressor must be able to maintain a minimum of 70 psi when the nailer is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 70 psi Min. 120 psi Max. 2. An oiler can be used to provide oil circulation through the nailer. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the nailer. 3. Use 3/8” air hoses with a minimum working pressure of 150 psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315” (8mm) on the nailer and a 3/8” quick coupler on the air hose. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the nailer between 70 and 120 psi. NO-MAR DECKING TIP The no-mar decking tip is designed to eliminate marks caused by the serrated work contact element (WCE). The no- mar tip may be removed if not required (See REMOVING NO-MAR DECKING TIP). Use tool in single cycle mode (SEE OPERATIONAL MODES) when no-mar tip is in place. REMOVING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove no-mar tip retaining ring. Retaining Ring No-Mar Tip 4. Pry no- mar tip away from the work contact element. Work Contact Element No- Mar Tip 5. Replace retaining ring onto no-mar tip, then store tip in safe place for future use. INSTALLING NO-MAR DECKING TIP 1. Disconnect air supply from nailer. 2. Remove all fasteners from magazine (See UNLOADING THE NAILER). 3. Remove retaining ring from no-mar tip. Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Oiler Regulator Filter Quick Plug 3 Operating Instructions 4. Carefully place no- mar tip over the end of work contact element. Position tip onto WCE making certain serrated gooves on each piece are in line and fit snugly together. Grooves 5. Position retaining ring on no- mar tip and press firmly in place. 6. Check that the WCE and trigger move up and down freely without sticking or binding. Operational Modes Always know the operational mode of the nailer before using. Failure to know the operational mode could result in death or serious personal injury. This stick framing nailer may be operated in the “Single Cycle” or the “Bottom Trip” mode. The nailer is delivered in the single cycle mode. A separate ‘red’ trigger for “Bottom Trip” mode is included with tool as an accessory. SINGLE CYCLE MODE When t...
Este manual também é adequado para os modelos :Pistola de pregos - FRAMING NAILER NS219001 (1.56 mb)
Pistola de pregos - FRAMING NAILER NS349001 (1.56 mb)
Pistola de pregos - FRAMING NAILER NS219500 (1.56 mb)