Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
• Make sure the WCE moves up and down without sticking or binding. If sticking or binding occurs, discontinue use of the nailer/stapler until proper service and/or repairs are performed • Connect the air supply to the nailer/stapler. • Press the WCE against the work piece without pulling the trigger. The nailer/stapler must not operate. • Hold the nailer/stapler clear of the work piece. The work contact element should return to its original down position. Pull the trigger. The nailer/stapler must not cycle. WARNING NEVER USE THE NAILER/STAPLER IF IT OPERATES WITHOUT PULLING THE TRIGGER Loading the Nailer/Stapler: WARNING CONNECT NAILER/STAPLER TO AIR SUPPLY BEFORE LOADING FASTENERS. DO NOT LOAD FASTENERS WITH TRIGGER OR SAFETY DEPRESSED TO PREVENT UNINTENTIONAL DISCHARGE OF A FASTENER. • Attach a high flow quick connector fitting to the nailer/stapler. • Use clean, dry, regulated, compressed air at 60 to 100 PSI (0.4 to 0.7 MPA). Do not connect the nailer/ stapler to any pressure source that may exceed 120 PSI (0.8 MPA). • Only use air hose that is rated for a maximum working pressure of at least 150 PSI (1.0 MPA) or 150% of the maximum system pressure, whichever is greater. • Press the magazine latch. Pull back the magazine cover. • Insert fasteners into magazine. Make sure the pointed ends of the fasteners are loaded with the sharp points facing points downward. Make sure the fasteners are not dirty or damaged. • Push the magazine cover forward until the latch catches. Operating the Nailer/Stapler: WARNING DO NOT DRIVE FASTENERS CLOSE TO THE EDGE OF THE WORK PIECE. THE WORK PIECE IS LIKELY TO SPLIT ALLOWING FASTENERS TO FLY FREE OR RICOCHET CAUSING PERSONAL INJURY. WARNING FIRE FASTENERS INTO WORK SURFACE ONLY. NEVER FIRE INTO MATERIALS THAT ARE TOO HARD TO PENETRATE. DO NOT DRIVE FASTENERS IN ON TOP OF OTHER FASTENERS OR WITH THE NAILER/STAPLER AT TOO STEEP AN ANGLE AS THE FASTENERS MAY RICOCHET CAUSING PERSONAL INJURY. 7 • For the nailer/stapler to operate, your finger must first be off the trigger and the work contact element of the nailer/stapler then pressed against the work piece. Once the work contact element is pressed against the work piece, pull the trigger to drive the fastener into the work piece. • Release the trigger after each fastener is driven. • Move the nailer/stapler to the next location and repeat the procedure above. • Test for proper fastener penetration by driving nails into a sample piece of wood. If the fasteners do not achieve the desired penetration, adjust the air pressure to a higher setting until the desired penetration is achieved. Clearing a Jam from the Nailer/Stapler: FASTENER JAMMED IN FASTENER DISCHARGE AREA: • Disconnect air nailer/stapler from air hose. • Open the nozzle, grab jammed fastener with pliers and remove. FASTENER JAM INSIDE THE MAGAZINE: • Disconnect air nailer/stapler from air hose. • Pull back on the magazine cover. • Open the nozzle and remove jammed fastener. • Push the magazine cover forward until the latch catches. Cleaning the Nailer/Stapler: WARNING DISCONNECT THE NAILER/STAPLER BEFORE CLEANING AND INSPECTION. CORRECT ALL PROBLEMS BEFORE PLACING NAILER/STAPLER BACK IN USE. DANGER NEVER USE GASOLINE OR OTHER FLAMMABLE LIQUIDS TO CLEAN THE NAILER/STAPLER. VAPORS IN THE NAILER/STAPLER WILL IGNITE WHEN NAILER/STAPLER IS IN USE AND CAUSE THE NAILER/STAPLER TO EXPLODE, WHICH WILL RESULT IN DEATH OR SERIOUS PERSONAL INJURY. • Disconnect air nailer/stapler from air hose. • Remove tar buildup with kerosene #2 fuel oil. Dry off nailer/stapler completely before use. • NOTE: DO NOT SOAK nailer/stapler in cleaning solutions or damage may occur. Service and Repairs: • All quality nailers will eventually require servicing or replacement of parts due to wear from normal use. These operations should only be performed by a licensed professional technician. Never try to repair the nailer/stapler by yourself. For service, call 1-800-423-3598. TROUBLESHOOTING GUIDE WARNING DISCONNECT NAILER/STAPLER FROM AIR SUPPLY BEFORE PERFORMING ANY SERVICE PROCEDURE. 8 Troubleshooting, continued Symptom: Air leak near top of nailer/stapler or in trigger area. Problem Solutions Loose screws. Tighten screws. Worn or damaged o-rings or seals Contact factory for service. 1-800-423-3598 Symptom: Nailer/stapler does nothing or operates sluggishly. Problem Solutions Inadequate air supply. Check compressor settings Check air hose/filters Inadequate lubrication. for kinks or blockage. Oil nailer/stapler per instructions. Worn or damaged o-rings or seals. Contact factory for service. 1-800-423-3598 Symptom: Air leak near bottom of nailer/stapler. Problem Solutions Loose screws. Tighten screws. Worn or damaged o-rings or bumper. Contact factory for service. 1-800-423-3598 Symptom: Nailer/stapler jams frequently. Problem Solutions Incorrect fasteners. Verify fasteners are the correct size. Damaged fasteners. Replace with undamaged fasteners Magazine or nose screw loose. Tighten screws. Magazi...
Este manual também é adequado para os modelos :Pistola de pregos - AIR-PLUS 691165 (457.57 kb)