Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
JAM RELEASE A tool-free jam release is provided for ease in clearing infrequent jams. NO-MAR PAD The no-mar pad prevents marring and denting when using the tool on softer woods. OIL-FREE DESIGN The oil-free design of the tool eliminates daily oiling and prevents oil splattering on work surfaces. OVERMOLD GRIP AND TRIGGER The overmold grip and trigger offer increased comfort and control of the tool. QUICK-CONNECT SWIVEL CONNECTOR The quick-connect swivel connector helps prevent hose tangles. SELECTABLE TRIGGER The selectable trigger lets the operator choose between Contact Actuation for higher productivity and Single Sequential Actuation for precise fastener placement. SIDE-LOADING MAGAZINE The side-loading magazine allows easy three-step reloading of fasteners. 9 ASSEMBLY UNPACKING This product has been shipped completely assembled. • Carefully remove the tool and any accessories from the box. • Make sure that all items listed in the packing list are included. • Inspect the tool carefully to make sure no breakage or damage occurred during shipping. • Do not discard the packing material until you have carefully inspected and satisfactorily operated the tool. • If any parts are damaged or missing, please call 1-866-539-1710 for assistance. PACKING LIST Brad Nailer Case Sample Fasteners Eye Protection Hex Keys (3 mm and 4 mm) Fastener Guide Operator’s Manual OPERATION WARNING: If any parts are missing do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. APPLICATIONS DANGER: You may use this tool for the purposes listed below: Do not use oxygen, combustible gases or bottled • Finish and Trim (interior and exterior) gases as a power source for this tool. The tool will • Decorative Trim explode and cause death or serious injury. • Book Cases • Baseboard WARNING: • Cabinets Do not allow familiarity with tools to make you • Case Backs careless. Remember that a careless fraction of a • Drawers second is sufficient to inflict severe injury. • Molding • Mirror and Picture Frames WARNING: • Paneling Always wear safety goggles or safety glasses with • Shoe & Base Moldings side shields when operating tools. Failure to do so • Staircases could result in objects being thrown into your eyes resulting in possible serious injury. • Upholstery Trim Panels • Wainscoting • Window Beading WARNING: • Chair Rail Disconnect the tool from the air supply before leaving the work area, moving the tool to another • Furniture Frames location, or handing the tool to another person. • Lattice Strip Molding Failure to do so could result in serious personal • Nailable Plastic Parts injury. • Crafts 10 11 Fig. 2 OPERATION WARNING: Always wear eye protection. Eye protection does not fit all operators in the same way. Make sure the eye protection chosen has side shields or provides protection from flying debris both from the front and sides. NO-MAR PAD See Figure 2. The no-mar pad attached to the nose of the tool helps prevent marring and denting when working with softer woods. WARNING: Disconnect the tool from the air supply before removing or replacing the no-mar pad. Failure to do so could result in serious personal injury. The pad can be removed by pulling it down and away from the nose. To replace the pad, fit it into place over the nose and push up to reseat. On-board storage for the pad is located on the magazine of the tool. An extra no-mar pad is provided in the on-board storage area. ADJUSTING THE EXHAUST See Figure 3. The adjustable exhaust on the end cap of the tool allows the operator to direct the exhaust according to operator preference. To adjust, turn the exhaust cap until the exhaust blows in the desired direction. Fig. 3 NOSE NO-MAR PAD ADJUSTABLE EXHAUST NO-MAR PAD STORAGE 12 OPERATION WARNING: Disconnect the tool from the air supply before leaving the work area, moving the tool to another location, or handing the tool to another person. Failure to do so could result in serious personal injury. CONNECTING THE TOOL TO AN AIR SUPPLY See Figure 4. DANGER: Do not use oxygen, combustible gases or bottled gases as a power source for this tool. The tool will explode and cause death or serious injury. This tool is designed to operate on clean, dry compressed air at regulated pressures between 70 and 120 psi . The correct air pressure is the lowest pressure that will do the job. NOTE: Air pressure that is higher than 120 psi may damage the tool. The tool and air hose must have a hose coupling that allows all pressure to be removed from the tool when the coupling is disconnected. WARNING: Always use a coupling that discharges all the compressed air in the tool at the time the fitting or hose coupling is disconnected. Using a ...