Assessments - 5, GPA: 4
(
)
)
|
Facilidade de uso
21). 5. Depress the quick release latch, close the fastener guide plate, and release the latch. NOSE CUSHION This tool is equipped with a rubber nose cushion (A) Fig. 22, that prevents marring of finished surfaces by the metal safety during normal operation. The nose cushion can be removed and stored in the rear area of the magazine (B) Fig. 22, when it is not required. CAUTION: Disconnect tool from air supply before removing or Fig. 22 A B reinstalling rubber nose cushion. MAINTENANCE CLEAN AND INSPECT DAILY CAUTION: Disconnect tool from air supply before cleaning and inspection.Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts. Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts. Keep all screws tight. Loose screws can cause personal injury or damage tool. If tool is used without an in-line oiler: place 5 or 6 drops of Porter-Cable Air Tool Oil into the air inlet of the tool at the beginning of each workday. 8 SERVICE AND REPAIRS All quality tools eventually require servicing or replacement of parts due to wear from normal use. Some user serviceable components are described in the TROUBLESHOOTING Section. Complete product Service is available from either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.). TROUBLESHOOTING CAUTION: Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of tool or in trigger area. Loose screws. Worn or damaged o-rings or seals. Tighten screws. Install “OVERHAUL” Maintenance Kit. 2. Tool does nothing or operates sluggishly. Inadequate air supply. Inadequate lubrication. Worn or damaged o-rings or seals. Verify adequate air supply. Put 5 or 6 drops of oil into air inlet. Install “DRIVER” Maintenance Kit. 3. Air leak near bottom of tool. Loose screws. Worn or damaged o-rings or bumper. Tighten screws. Install “OVERHAUL” Maintenance Kit. 4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of correct size. Damaged fasteners. Magazine or nose screws loose. Replace w/undamaged fasteners. Tighten screws. Magazine is dirty. Driver is worn or damaged. Clean magazine. Install “DRIVER” Maintenance Kit. 5. Other. Contact a Porter-Cable Service Facility. 9 ACCESSORIES The testing of this tool has been accomplished with the following accessories. For safest operation, it is recommended that only these accessories be used with this product. WARNING: Since accessories other than those listed have not been tested with this product, use of such accessories could be hazardous. CATALOG NO. DESCRIPTION LENGTH GAUGE QUAN/BOX BN18075 18 Ga. Brad Nail, 3/4" 3/4" 18 5000 BN18075-1 1000 Pk. of BN18075 3/4" 18 1000 BN18100 18 Ga. Brad Nail, 1" 1" 18 5000 BN18100-1 1000 Pk. of BN18100 18 1000 BN18119 18 Ga. Brad Nail, 13/16" 13/16" 18 5000 BN18125 18 Ga. Brad Nail, 11/4" 11/4" 18 5000 BN18125-1 1000 Pk. of BN18125 18 1000 BN18150 18 Ga. Brad Nail, 11/2" 11/2" 18 5000 BN18156 18 Ga. Brad Nail, 19/16" 19/16" 18 5000 BN18175 18 Ga. Brad Nail, 13/4" 13/4" 18 5000 BN18200 18 Ga. Brad Nail, 2" 2" 18 5000 60061 “OVERHAUL” Maintenance Kit 60063 “DRIVER” Maintenance Kit 884293 Oil (for Air Tools) 893579 Safety Glasses 893933 Bottom Fire Trigger PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof of purchase may be required. This warranty does not apply to O-rings and Driver Blades or to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service Centers or Authorized Service Stations. ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PURCHASE. To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, P....
Este manual também é adequado para os modelos :Pistola de pregos - BN200A (793.18 kb)