Assessments - 3, GPA: 4.7
(
)
)
|
Facilidade de uso
(102 cm) Coin Slide Models *4.5 in. (11.4 cm) *15.44 in. (39.2 cm) 21.56 in. (54.8 cm) Coin Slide Models *38.19 in. (97 cm) Electronic Control Models *43 in. (109.2 cm) Standard Capacity Meter case *43.875 in. (111.4 cm) High Capacity Metercase DRY2238 GAS MODELS 23.5 in. (59.7 cm) 8.0 in. (20.3 cm) 28 in. (71.1 cm) *38.19 in. (97 cm) Electronic Control 15.4 in. (39.1 cm) 2.3 in. (6 cm) 26.875 in. (68.3 cm) 0.4 in. (1.02 cm) 2.8 in. (7 cm) 1 22.06 in. (56 cm) Electronic Control Models *4.5 in. (11.4 cm) *40.19 in. (102 cm) Coin Slide Models 4.0 in. (10.2 cm) *15.44 in. (39.2 cm) *36 in. (91.4 cm) 21.56 in. (54.8 cm) Coin Slide Models *43 in. (109.2 cm) Standard Capacity Meter case *43.875 in. (111.4 cm) High Capacity Metercase Installation Before You Start Tools For most installations, the basic tools you will need are: D818I 1 Wrench 2 Screwdrivers 3 Level 4 Teflon Tape 5 Duct Tape 1 2 3 45 Figure 1 NOTE: An 8 in. (20.32 cm) coin drawer is required for coin operated MDC and NetMaster models with standard capacity meter case and high capacity meter case models starting with Serial Nos. beginning 1010. High capacity meter case MDC and NetMaster models with Serial Nos. beginning 0910 through 1010 require a 7.21 in. (18.31 cm) coin drawer. Card Reader Models The machine is shipped from the factory with the Electronic Control Diagnostic Harness Assembly unplugged. To avoid unauthorized manual programming or vending perform the following steps. 1. Open service door. Refer to Figure 2. 2. Locate diagnostic harness on electronic control. 3. Plug connectors for “white/black” wire and “red/ blue” wire together. . 1 FLW6R 1 Service Door Figure 2 Any disassembly requiring the use of tools must be performed by a suitably qualified service person. W299 WARNING 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680 Installing the Dryer Step 1: Position and Level the Dryer Install dryer before washer. This allows room for attaching exhaust duct. Install the four rubber feet (in accessories bag). Select a location with a solid floor. Dryers installed in residential garages must be elevated 18 inches (46 cm) above the floor. No other fuel burning appliance should be installed in the same closet with the dryer. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. The dryer needs sufficient clearance and an adequate air supply for proper operation and ventilation, and for easier installation and servicing. (Minimum clearances are shown in Figure 4). Place the dryer in position, and adjust the legs until the dryer is level from side to side and front to back. Leveling legs can be adjusted from inside the dryer with a 1/4 in. driver. All four legs must rest firmly on the floor so the weight of the dryer is evenly distributed. The dryer must not rock. D678I 1 Dryer Base 2 Level 3 Leveling Leg 4 Rubber Foot 1 2 3 4 Figure 3 Installation IMPORTANT: In mobile home installations, gas dryers MUST be permanently attached to the floor at the time of installation. Order No. 526P3 Hold Down Kit (available at extra cost) for a manufactured (mobile) home installation. Follow the instructions supplied with the kit. Installation of unit must conform to the Manufactured Home Construction and Safety Standards, Title 24 CF4, Part 32-80 or Standard CAN/CSA-Z240 MH. 512680 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 9 Installation D337I 1 Closet Door 2 Centered Air Openings (G) (2 Openings minimum) 3 Outer Wall of Enclosure **NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting easier to connect. 1 2 (G) 3 A E **42 in. (106.7 cm) F F B A A C FRONT VIEW (W/O CLOSET DOOR) SIDE VIEW (CLOSET DOOR) FRONT VIEW (CLOSET DOOR) D Area Description Free Standing/AlcoveInstallation Closet Installation A Dryer sides and rear clearance 0 in. (0 cm) 0 in. (0 cm) B Dryer top clearance 12 in. (30.5 cm) 12 in. (30.5 cm) C Dryer front clearance Not Applicable 2 in. (5.1 cm) D Exhaust duct clearance to combustible material 2 in. (5.1 cm) 2 in. (5.1 cm) E Weather hood to ground clearance 12 in. (30.5 cm) 12 in. (30.5 cm) F Distance from floor or ceiling to hole edge Not Applicable 3 in. (7.6 cm) G* Area of centered air openings in closet door Not Applicable 40 sq. in./open (260 sq. cm) *Louvered door with equivalent air openings is acceptable. (Minimum clearances are shown.) Figure 4 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680 Installation Step 2: Connect Dryer Exhaust System WARNING To reduce the risk of fire and combustion gas accumulation the dryer MUST beexhausted to the outdoors. W604 To reduce the risk of fire and the accumulation of combustion gases, DO NOT exhaust dryer air into a window well, gas vent, chimney or enclosed, unventilatedarea, such as an attic, wall, ceiling, crawl space under a building or concealed space of a building. W045 WARNING This gas appliance contains or produ...