Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
INSTALLATION Parts and literature are packaged inside your dryer drum. To install: 1. Move your dryer to an appropriate location for installation. Consider installing the dryer and washer side-by-side, to allow access to electrical, and exhaust connections. Lay two of the carton cushion-tops on the floor. Tip your dryer on its side so it will lay across both cushion-tops. 2. Set your dryer back in an upright position. 3. Review the Exhausting section before installing the exhaust system. Install the ductwork from your dryer to the exhaust hood. The crimped end of the duct sections must point away from your dryer. DO NOT use sheet metal screws when assembling ducting. These joints should be taped. Never use plastic flexible exhaust material. Tip for tight installations: install a section of exhaust system to your dryer before putting it in place. Use duct tape to secure this section to your dryer, but do not cover louvers in dryer cabinet. 4. Review Electrical Requirements section. BEFORE OPERATING OR TESTING, follow the grounding instructions in the Grounding section. 5. With a level, check your dryer and make necessary adjustments to the leveling legs. 6. At this time, make sure all exhaust and electrical connections are complete. Plug in your dryer, and check operation by using the checklist below. FINAL INSTALLATION CHECKLIST . Dryer is plugged into electrical outlet and properly grounded. . Exhaust ductwork is hooked up and joints taped. . Plastic flexible duct is NOT used. . Use rigid or stiff-walled flexible metal vent material. . Dryer is level with all legs firmly on the floor. . Start your dryer to confirm that it runs, heats, and shuts off. SAMSUNG Dryer Owner’s Instructions A-5 Installation Instructions Dryer Exhaust Tips WARNING: Plastic or non-metal flexible duct presents a potential fire hazard. 1 2 3 4 1. Let your dryer exhaust the air easily. 2. Use4”diameter rigid metal duct.Tapealljoints, including at the dryer. Never use lint-trapping screws. 3. Keep ducts as straight as possible. 4. Clean all old ducts before installing your new dryer. Be sure vent flap opens and closes freely. Inspect and clean the exhaust system annually. Don’t let a poor exhaust system slow drying by: 1 2 3 4 1. Restricting your dryer with a poor exhaust system. 2. Using a plastic, thin foil, or non-metal flexible duct. 3. Using unnecessarily long duct runs with many elbows. 4. Allowing crushed or clogged ducts and vent. Installation Instructions Installation Instructions Door Reversal 1. Unplug power cord. 2. Remove two door hinge screws. 3. Lift the door and remove from dryer. 4. Remove two screws on the opposite side of door hinge. 5. Remove two screws on holder lever. 6. Place the door on the other side and reattach it to dryer. 7. Reassemble holder lever. 8. Reassemble the screws in the remaining holes. SAMSUNG Dryer Owner’s Instructions A-7 B-1 SAMSUNG Dryer Owner’s Instructions . Control Features vary by model. OVERVIEW OF THE CONTROL PANEL Operating Instructions, Tips Operating Instructions, Tips Operating Instructions, Tips 1. Digital Graphic Display The display window shows the estimated time remaining in the cycle after the Cycle Selector dial is pressed. The estimated time remaining may fluctuate as the cycle progresses. The Drying light will illuminate and remain lit until the cycle is complete. When your dryer is in the cool-down phase, the Cooling light will illuminate. When your dryer is in the wrinkle prevent phase, the Wrinkle Prevent light will illuminate. Whenthecycleiscomplete,“END”willappear in the display panel until the dryerdoor is opened or Power key is pushed. If your dryer is paused during a cycle, the indicator lights will blink until the Cycle Selector dial is pressed. 2. Dry Level Selection Button To select the dry level in the Normal, Heavy Duty, or other Sensor Dry cycles, press the Dry Level button. An indicator light will illuminate next to the desired dryness level. Press the button repeatedly to scroll through the settings. Larger or bulkier loads may require the Very Dry (select models) or More Dry setting for complete dryness. The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle. Damp Dry (select models) is designed to partially dry items. Use for items that lay flat or hang to dry. 3. Temp Selection Button To select the correct temperature for the load, press the Temp button. An indicator light will illuminate next to the desired temperature. Press the button repeatedly to scroll through the settings. High – For sturdy cottons or those labeled Tumble Dry. Medium – For permanent press, synthetics, lightweight cottons, or items labeled Tumble Dry Medium. Medium Low – For lower heat than Medium to dry synthetic or washable knit fabrics. Low – For heat sensitive items labeled Tumble Dry Low or Tumble Dry Warm. Extra Low – Provides the lowest heated dry temperature possible. 4. Time Selection Button When usin...
Este manual também é adequado para os modelos :Secadores - Electric Dryers DV306L (2.91 mb)