Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
On electric dryers, exhausting can be on the cabinet right or left side, or through the dryer bottom. Gas dryers can exhaust on the cabinet right side or the dryer bottom. To change exhaust direction you will need Exhaust Kit Pub. No. 14-A018 and a rigid metal 4. 90-degree elbow. The kit is available through your GE retailer. Follow the instructions supplied with the kit. Same as other side EXHAUST DUCT LOCATING DIMENSIONS 3 3/4. (9.5 cm) 3 3/4. (9.5 cm) 13 5/16. (34 cm) 4 3/8. (11 cm) 5 7/8. (15 cm) GAS SUPPLY REQUIREMENTS Replace brass connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used. WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury. Always use NEW flexible connectors when installing a gas appliance. 1. Installation MUST conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) or in Canada, the current CAN/CGA B149. 2. The gas supply line should be of 1/2. (1.27 cm) rigid pipe. 3. If codes allow, flexible metal tubing may be used to connect your dryer to the gas supply line. The tubing MUST be constructed of stainless steel or plastic-coated brass. 4. The gas supply line MUST have an individual shutoff valve. 5. A 1/8. (0.32 cm) NPT plugged tapping, accessible for test gauge connection, MUST be installed immediately upstream of the gas supply connection to the dryer. 6. The dryer MUST be disconnected from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures in excess of 1/2 psig (3.45 kPa). 7. The dryer MUST be isolated from the gas supply piping system during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.45 kPa). 13 Installation Instructions LOCATION OF YOUR DRYER Do Not Install the Dryer: 1. Do not install the dryer in an area exposed to dripping water or outside weather conditions. 2. Do not install the dryer in an area where it will come in contact with curtains, drapes or anything that will obstruct the flow of combustion and ventilation air. 3. Do not install the dryer on carpet. Floor MUST be solid with a maximum slope of 1. (2.54 cm). Undercounter Installation: If an undercounter* installation is desired, the dryer MUST have a top sheet kit installed, Pub. No. 14–A008. Kit is available through your GE retailer. *Custom-sized countertop is required. Installation in Recess or Closet: 1. This dryer MUST be exhausted outdoors. 2. No other fuel burning appliance shall be installed in the same closet as the GAS DRYER. 3. Your dryer needs the space around it for proper ventilation. DO NOT INSTALL YOUR DRYER IN A CLOSET WITH A SOLID DOOR. 4. Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If the closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed. Air openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable. 60 sq. in. (387.1 sq. cm) 60 sq. in. (387.1 sq. cm) Closet door 3 in. (7.6 cm) 3 in. (7.6 cm) 0. (0 cm) 0. (0 cm) 3. (7.6 cm) Allow the following clearances for ease of installation: FRONT SIDES REAR TOP Alcove, stack, 3” (7.6 cm) 0 (0 cm) 3” (7.6 cm) 0 (0 cm) undercounter or closet THIS DRYER MUST BE EXHAUSTED OUTDOORS. 5. The following illustrations show minimum clearance dimensions for proper operation in a recess or closet installation. 3. (7.6 cm) 14 Installation Instructions MOBILE HOME INSTALLATION 1. Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4. (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. 2. If the dryer is exhausted through the floor, the exhaust system MUST NOT terminate beneath the mobile home. Termination MUST be securely fastened to the mobile home structure. 3. When installing a gas dryer into a mobile home, a provision must be made for outside make-up air. This provision is to be not less than twice the area of the dryer exhaust outlet. 4. Gas dryers MUST be fastened to the floor using Mobile Home Installation Kit Pub. No. 14–D346–33. 5. See the Exhaust System Requirements section for other important venting information. 6. Installation MUST conform to current Manufactured Home Construction & Safety Standard (which is a Federal Regulation Title 24 CFR—Part 32–80) or, when such standard is not applicable, with American National Standard for Mobile Homes, ANSI/NFPA No. 501B. In Canada, the CSA Z240 is applicable. Correct Do Incorrect Don’t Don’t Don’t The dryer is designed under ANSI Z 21.5.1. ROUGH-IN DIMENSIONS 47 1/2. (120.7 cm) 3/4. (1.9 cm) Door open 90° 4 3/8. (11.1 cm) Optional vent knockout 25 3/4. (65.4 cm) ...
Este manual também é adequado para os modelos :Secadores - PSXH43 (478.25 kb)