Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
DO NOT install your dryer in a closet with a solid door. 4. Closet door ventilation required: A minimum of 120 square inches (774.2 cm.) of opening, equally divided at the top and bottom of the door, is required. Openings should be located 3 inches (7.6 cm) from bottom and top of door. Openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable. 60 sq. in. (387.1cm.) 3” (7.6cm) 60 sq. in. (387.1cm.) 3” (7.6cm) MINIMUM INSTALLATION CLEARANCES - Inches (cm) SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a UnderCounter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.54 cm) * For other than straight back venting, a quick-turn 90° dryer vent elbow (vented right or down in free-standing dryer or right on pedestal-mounted dryer) must be installed to achieve 0” (0 cm) installation. 0” (0cm) 0” (0cm) 1” (2.54cm) 0” (0cm) To achieve an installation with 0” (0 cm) clearance for the back of the dryer (for other than straight back venting), a quick-turn 90° dryer vent elbow must be installed as described previously in this manual. closet door 7 36.0” (91.5cm) 16.9” (43cm) 19.0” (48cm) 51.25” (130cm) 1.6” (4cm) 3.75” (9.5cm) 13.50” (34.5cm) to center of rear vent 3.7” (9.5cm) gas supply pipe on rear of gas unit 48.25” (122.5cm)* to clear open door 30.5” (77.5cm)* to front of closed door 27.0” (68.5cm) centerline height for rear vent electrical supply on rear of unit freestand dryer on floor floor line floor line dryer mounted on optional pedestal * To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right or down on freestanding dryer) adds approximately 0.75 in. (2.0 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestanding dryer adds approximately 4 in. (10.2 cm) to installation depth. Leftward venting on pedestal-mounted or freestanding dryer adds approximately 3.75 in. (9.5 cm) to installation depth. Downward venting of exhaust on pedestal-mounted dryer adds approximately 2.25 in. (5.7 cm) to installation depth. * To obtain these minimal depth dimensions, dryer must be vented straight back. Using a quick-turn 90° elbow (right) adds approximately 0.75 in. (2 cm) to installation depth. Upward venting of exhaust on stacked dryer adds approximately 4 in. (10.2 cm) to installation depth. Downward venting of exhaust on stacked dryer adds approximately 2.25 in. (6.5 cm) to installation depth. Leftward venting of exhaust on stacked dryer adds approximately 3.75 in. (9.5 cm) to installation depth. 71.5” (182cm) 39” (99cm) 37” (94cm) gas supply pipe on rear of gas unit 48.25” (122.5cm)* to clear open door 30.5” (77.5cm)* to front of closed door centerline height for rear vent electrical supply on rear of unit 27.0” (68.5cm) Installed dryer dimensions 8 Electrical installation The following are specifi c requirements for proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fi re hazard. - ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fi re hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. - ELECTRICAL SHOCK HAZARD • A U.L.-approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. • Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. Dryers operating on 208 volt power supply will have longer drying times than dryers operating on 240 volt power supply. Grounding requirements - Electric dryer (USA) -ELECTRICAL SHOCK HAZARD -Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. After you purchase and install a 3 wire or 4 wire power supply cord having an equipment-grounding...