Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
If meter reads 120V, check the rest of the heater circuit. E68 Key (button) Struck Fault One of the keys (buttons) is stuck closed (active). Enter function test mode and perform key (button) test to determine which button is at fault. Carefully free the and perform the test again. If button is free but the key struck code still exists, replace electronic control. E8C Too many trips in a period of time. The safety (high limit) thermostat has tripped too many times within a certain period of program time. Check for blocked lint filter, blocked exhaust, air leaks around air duct, broken blower fan blades, worn or loose drum seals, dryer installed in closet with solid doors or door seal not correctly seated. EAF Watch Dog Reset Microcontroller has been reset by internal Watchdog timer. Clear code, exit mode and start dryer. If problem persists, replace electronic control. 137058000A 0808 FUNCTION TEST SEQUENCE 1. Non-Digital Readout Display Models: Position the cycle selector knob to the 12 O’clock position. Digital Readout Display Models: Position the cycle selector knob to the Normal cycle option. 2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds. 3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds. The control will enter test mode, the buzzer will sound 3 times and all LED’S will rapidly flash. After entering the test mode, the program knob can now be rotated to select the following tests: Rotate the program knob clockwise from the start position: 1 turn: Drive motor runs; heat source is on. Drying LED is lit. “H” and the control thermistor reading will toggle back and forth in the display.** 2 turns: Drive motor runs; heat source is off. Cool Down LED is lit and “AF” (Air Fluff) is displayed. 3 turns: Drive motor runs; heat source is off. Drying and Cool Down LED’s are lit and numbers appear in the display showing moisture sensor readings. Opening the door (press in on door switch plunger) and placing a finger on the both moisture sense bars at the same time will make the numbers decrease. In controls that do not have a digit display, the MORE DRY LED should be ON. Opening the door (press in on door switch plunger) and placing a finger on the both moisture sense bars at the same time will make the DAMP LED come on. 4 turns: Drive motor runs; heat source is off. Key test: a. When the TEMP button is pressed, all the TEMP LED’s should light. If the Temp selector is the rotary knob, and the knob is rotated, there should be a key beep with each setting. b. When the DRYNESS button is pressed, all the dryness level LED’s should light. c. When the OPTION or Select button is pressed, all the Option LED’s should light. d. When the START button is pressed, all the cycle status LED’s should light. e. When the Pause Cancel button is pressed, all the Cycle status LED’s should light. 5 turns: Drive motor runs; heat source is off. Cool Down LED is lit. Control thermistor reading is displayed.** 6 turns: Drive motor runs; heat source is on. Drying LED is lit. Control thermistor reading is displayed.** **For models that do not have a digital display, the dryness LED’S could be used to determine the control thermistor temperature reading. The number of flashes of the bottom three LED’S will determine the value of the temperature as follows. EXAMPLE: Normal flashes 1 time (Normal = HUNDRED’S) Less Dry flashes 2 times (Less Dry = TEN’S) Damp flashes 6 times (Damp = ONE’S) Temperature = 126° To EXIT the test mode, press and hold the SELECT and Pause Cancel buttons simultaneously for six seconds or disconnect power from dryer. Dryer will be reset for regular operation. 137058000A 0808 Fiche technique De Technologie De Secheuse Cette information est prevue pour les techniciens qualifies seulement. ATTENTION : DEBRANCHEZ LE COURANT ELECTRIQUE AVANT D'ENTRETENIR svp le retour que cette feuille a son enveloppe dans le produit pour de futures De CODES De DEFAUT De LECTURE 1. Modeles sans afficheur numerique : Placez le selecteur de cycle aux 3 heures de position. Modeles avec afficheur numerique : Tournez le bouton de selection de cycle dans le sens des aiguilles d’une montre de 3 reglages a partir de l’option de cycle Normal. 2. Serrez et tenez le CHOISI ET LA PAUSE (annulation) se boutonne simultanement pendant six secondes. 3. Juste apres, serrez et tenez le PAUSE – ANNULATION ET METTEZ EN MARCHE les boutons pendant 6 secondes 4. Modeles avec afficheur numerique : Tournez le bouton de minuterie de 1 clic dans les sens inverse des aiguilles d’une montre. Le code d'erreur apparaitra dans l'affichage de chiffre. Modeles sans afficheur numerique : Tournez le bouton de selecteur de cycle jusqu aux 2 heures de position. Les quatre voyants de signalisation du sechage, refroidissent, ride debarrassee, et la rotation propre de filtre de fibre clignotera le nombre de fois pour le premier chiffre du code et le voyant de signalisation de DEBUT clignotera le nom...