Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
• Extend the antenna on the Parent unit (B-3) to get the best reception. • If required, re-adjust the SENSITIVITY control (A-5) on the Baby unit to set the level at which the microphone will start to pick up sounds. When the SENSITIVITY control (A-5) is set to 9, the microphone picks up even the softest sounds. Experiment with different levels until you find the setting that suits you and your baby best. The green LINK light (B-1) lights continuously when the Parent unit and the Baby unit are in touch with each other. 4 ADDITIONAL FEATURES Avoiding interference Both units use anti-interference technology to reduce the chance of interference from other signals. If interference does occur or if sound reception is poor, try switching both units to the other channel to improve the sound quality. Note: Always make sure that the channel selection switches (A-7, B-8) on both units are set to the same position. Checking that the units are in touch The green LINK light (B-1) of the Parent unit lights continuously to show that the Parent unit and the Baby unit are in touch with each other. This light flashes if the Baby unit is out of range for more than 30 seconds or if the signal is blocked. When the units are no longer in touch, try one of the following: • Move the Parent unit closer to the Baby unit. (The maximum operating distance is 250m in ideal conditions. Walls and floors can limit this distance.) • Switch both units to the other channel. • Check that both units are powered correctly (low batteries?). Switching on the audible warning If you wish, you can switch on a special feature that lets you hear an audible warning on the Parent unit when the units are not in touch. The Parent unit is delivered with this beep switched off to avoid intermittent disturbances that can occur when the connection is interrupted for a short period. To switch on the audible warning, open the Parent unit’s battery compartment cover (B-9) and set the switch (B-12) inside to the On position ( ). Note: The LINK light (B-1) continues to operate even if the audible warning is switched off. Belt clip When the batteries of the Parent unit are charged, the unit can be carried around giving you freedom of movement while still monitoring your baby. Use the belt clip (B-7) to attach the unit to your clothing and so keep your hands free. 5 PROBLEM SOLVING Problem Possible Cause Solution Power light does not light (Parent unit). Unit is not turned on. Batteries are low. Turn Volume control/Off switch clockwise (B-5). Recharge batteries. Power light does not light (Baby unit). Unit is not turned on. AC adapter is not plugged in or Batteries are exhausted. AC adapter plugged into an outlet that is not working. Push the Power switch (A-4) to switch on the unit. Plug in AC adapter or replace batteries. If the power socket has a switch, turn it on. High pitched noise. Units are too close together. Volume too high. Move Parent unit away from Baby unit. Turn volume control on Parent unit counter-clockwise. No sound. Volume control on Parent unit is set too low. Units are out of range. Turn volume control/Off switch clockwise (B-5). Move Parent unit closer to Baby unit. Power light blinking. Batteries are low or empty. Parent unit:- recharge batteries. Baby unit:- replace batteries or connect to mains power. Interference or poor reception. Mobile or cordless phones too close to the baby monitor can cause interference. Move the phones away from the units. 6 TECHNICAL SPECIFICATIONS Power supply – Battery pack; rechargeable NiMH for Parent Unit (included); – Optional batteries 4 x 1.5V; AA alkaline for Baby Unit (not included); – AC power adapter 230V AC, 50 Hz (two included): - Output voltage 9V DC, 200mA. Only use the AC power adapter included or a type that complies with safety standard EN60950 and that has the following specification: 9 Volt DC / 200mA. Operating range – up to 250 metres in ideal conditions – 10°C to 40°C Pilot tone – Continuous communication link (hidden signal ensures a continuous link between both units so you only hear your baby’s sounds). Transmission frequencies Channel A Channel B SBC SC368/86U & SBC SC368/87U: 40.695 MHz 40.675 MHz SBC SC368/05U (IRE, UK): 49.890 MHz 49.830 MHz SBC SC368/13U (SE): 27.145 MHz 27.095 MHz SBC SC368/16U (ES): 31.350 MHz 31.000 MHz 7 UNITE BEBE A-1 Microphone ------------------------microphone tres sensible A-2 Temoin d’alimentation ----------s’allume quand l’unite est active; clignote quand les piles sont faibles A-3 Temoin de transmission --------s’allume quand un son est en cours de transmission A-4 Bouton poussoir Power F (Alimentation) -------------------appuyez sur ce bouton pour mettre l’unite sur tension ou hors tension A-5 Sensibilite Microphone ----------regle le niveau a partir duquel le microphone enregistrera les signaux sonores A-6 Prise d’alimentation elect. c.c. --------------------------enfichez le connecteur d’adaptateur reseau dans cette prise A-7 Selecteur de canal ----------...
Este manual também é adequado para os modelos :Secadores - BABY MONITOR SBC SC368 (650.2 kb)