Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
21 PL04 - HIGH COOL DOWN TEMPERATURE/TIME (HICd) The first part of this program controls the cool down temperature when the Phase 5 microprocessor controller (computer) is used in the automatic mode. The cool down temperature is programmable from a minimum of 70° F to a maximum of 190° F in ten-degree increments or from a minimum 21° C to a maximum of 88° C in five-degree increments. For the AD-26 and AD-295 any three (3) of the selections (HI/LO/PP) are programmable from a minimum of 100° F to a maximum of 170° F in ten-degree increments or from a minimum of 38° C to a maximum of 77° C in five-degree increments. For the AD-540 and WDA-540 any three (3) of the selections (HI/LO/PP) are programmable from a minimum of 100° F to a maximum of 160° F in ten-degree increments or from a minimum of 38° C to a maximum of 71° C in five-degree increments. The second part of this program controls the cool down time for both the automatic and timed modes. The cool down time can be programmed from a minimum of 0 to a maximum of 9 minutes. NOTE: When the Phase 5 microprocessor controller (computer) is used in the automatic mode, at the end of the drying cycle, the Phase 5 microprocessor controller (computer) will start the cooling cycle for the cool down time programmed or until the temperature has dropped to the programmed cool down temperature, whichever of the two (2) comes first. PL05 -LOW TEMPERATURE (LO°F) Same as PL03 but for Low Temperature program. PL06 -LOW COOL DOWN TEMPERATURE/TIME (LOCd) Same as for PL04 but for Low Cool Down Temperature/Time. PL07 -PERMANENT PRESS (PP°F) Same as PL03 but for Permanent Press. PL08 -PERMANENT PRESS COOL DOWN TEMPERATURE/TIME (PPCd) Same as PL04 but for Permanent Press Cool Down Temperature/Time. PL09 -LEFT COIN SLOT DENOMINATION (LCdE) In the case of a single coin acceptor, this program setting is determined by the value of the coin acceptor (i.e., 25.). When a dual coin acceptor is used, the program setting is determined by the left coin slot coin acceptor value (lower coin value). Program settings are from a minimum of 1 to a maximum of 9999. 22 PL10 -RIGHT COIN SLOT DENOMINATION (rCdE) This program need only be set when a dual coin acceptor is used. The program setting is determined by the value of the right coin acceptor slot (higher value). Program settings are from a minimum of 1 to a maximum of 9999. When used in conjunction with the Left Coin Slot Denomination program, the Phase 5 microprocessor controller (computer) automatically calculates the ratios necessary for coin insertion time values. PL11 -TIME FOR AMOUNT TO START (tFAS) This program is set for the specific value in TIME that will be vended for the programmed “Amount To Start” (“AtSt”) the dryer. For example, if 25. is required to start the dryer for 10 minutes, the settings would be... PL11 “Time for Amount To Start” ..........“tFAS” = 10 PL12 “Amount To Start” ......................... “AtSt” = 25 In addition, with the “Time For Amount To Start” (“tFAS”) and the “Amount To Start” (PL12 - “AtSt”) programmed along with the type of coin acceptor (denominations) on the dryer (i.e. 10./25.), the Phase 5 microprocessor controller (computer) will do ALL calculations and vend the correct amount of time for any coin inserted after the initial “Amount To Start” has been inserted - including both accumulative coin program settings. For example, if a dryer is equipped with a 10./25. dual coin acceptor and the desired “Amount To Start” (“AtSt”) is 55. for 33 minutes (“tFAS”), with the microprocessor controller (computer) set for accumulative time 10./25. dual coin acceptor and the desired “Amount To Start” (“AtSt”) is 55. for 33 minutes (“tFAS”), with the microprocessor controller (computer) set for accumulative time, after initial “Amount To Start” is inserted (55.), each additional 10. inserted would yield 6 minutes, and each additional 25. inserted would yield 15 minutes. PL12 -AMOUNT TO START (AtSt) This program sets the “Amount To Start” the dryer and can be programmed from a minimum of 1 to a maximum of 9999. PL13 -MINIMUM AMOUNT FOR ADDITIONAL TIME (AFAt) This program need only be set when the Phase 5 microprocessor controller (computer) is set in the “Accumulative Coin” (“ACOn”) mode (PL01). The value set for this program is what will have to be inserted for more time after the “Amount To Start” (“AtSt”) has been inserted. Example No. 1: “Amount To Start” (“AtSt”) is 50. for 30 minutes and an additional 50. is required for more time. In this example PL13 should be set for 50.. PL14 -MAXIMUM TIME FOR AUTOMATIC DRY (Adrt) This program is used only when the Phase 5 microprocessor controller (computer) is set in the Automatic Mode. This program controls the maximum time the dryer will run even if the Dryness Level program (PL02) has not been reached. 23 PL15 -ANTI-WRINKLE TIMING 1. Guard Delay Time (GdLY) This program controls the dwell (stop) time and activation of anti-wrinkle “Guard On Time” (“Gont”). The dwell (...
Este manual também é adequado para os modelos :Secadores - Gas Electric Steam AD-540 (501.81 kb)
Secadores - Gas Electric Steam WDA-540 (501.81 kb)
Secadores - Gas Electric Steam AD-295 (501.81 kb)