Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
Water “droplets” off when solution is off and they are flashing when solution is on. “Battery” blinks when Screens low voltage occurs. Arrows indicating vacuum status. AvailableThey are flashing when vac is on to Operator and off when vac is off. SCREEN 2 Example SCREEN 3 (Diagnostic) The Diagnostic only. It will not show unless a fault with the machine occurs. When the fault happens the icon and error code will be displayed. CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -7 Machine Control Panel Machine Control Panel The key switch turns “ON” the power to the control panel. “O” is the “OFF” and “I” is the “ON”. Brush Up/Down Switch (See figure 1, Item A) To lower brush head, push the brush switch in the down (+) position. To lower the brush head to maximum brush pressure, continue to hold the switch in the down (+) position until the travel stops. The brush motors will start and solution will flow (provided the solution is turned “ON”) when the machine begins to traverse. To raise the brush head, push the brush switch in the up (-) position until the brush head travel stops or desired position is reached. Squeegee Up/Down Switch (See figure 1, Item B) The squeegee switch is used to raise and lower the squeegee and to turn on and off the vacuum motor. The vacuum motor is turned on when the switch is placed in the middle or lower position. NOTE: When the squeegee switch is placed in the lower position, the vacuum motor will turn on. To raise the squeegee, place the switch in either the middle or up position. The middle position is used for one touch control. The vacuum motor will stop, after a short delay, when the switch is placed in the up position. Hour Meter (See figure 1, Item E) The hour meter is located on the front display. You must toggle screens using LCD display button. The hour meter indicates the number of hours the machine has operated. It displays brush motor, vacuum motor, traverse motor and total key on times. Battery Meter (See figure 1, Item F) The battery meter indicates the relative charge on the battery pack. The battery meter is located on screen 1 on the front display. See page 7. Solution Flow Control (See figure 1, Item C) The solution flow switch regulates the flow of chemical solution to the floor. To increase the flow, toggle (+). To decrease the flow, toggle (-). To shut off the solution, toggle - until no indicators are visible on display. NOTE: DO NOT run dry! NOTE: No solution will flow when the machine does not traverse. Circuit Breakers The circuit breaker reset buttons are located on the back side of the front cover below front display. The breakers are as follows: Item A - Main (5 amp) Item B - Key Switch (5 amp) A B C DE, F E Figure 1 Page -8-CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Machine Controls and Features Machine Controls and Features The Scrubtec R is equipped with a float that shuts the vacuum off when the recovery tank is full. The squeegee will no longer pick up water. If this should happen, raise the squeegee and empty the recovery tank. The Traverse The Scrubtec R is equipped with an electronically controlled traverse system with variable speeds in forward and reverse. 1. To traverse the machine, the power to the machine must be turned on with the key switch and the operator must be properly seated. 2. The traverse speed can be adjusted by varying the pressure on the foot pedal. NOTE: During reverse motion, the squeegee raises and the solution flow stops automatically. Reverse also reduces maximum traverse speed. Brakes The machine is equipped with an electronic braking system. The electronic braking is activated automatically. NOTE: During training, you should allow machine to come to a full stop until you become familiar with stopping distances required. Parking Brake The parking brake is activated automatically when the machine comes to a stop. It disengages automatically when you begin to traverse. The transaxle is equipped with a manual brake release. NOTE: Machine will not function when manual brake release is engaged. See figure 2. Reverse Alarm The reverse alarm will sound intermittently and automatically when the machine is in reverse. Figure 2 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -9 How To Prepare the Machine For Operation How To Prepare the Machine For Operation The machine is packed in a specific package provided on a pallet so that it can be moved with a forklift. WARNING: The packages cannot be placed ontop of each other. How to Unpack the Machine 1. Remove the outer package. 2. The ...
Este manual também é adequado para os modelos :Secadores - 571 (1.5 mb)
Secadores - 571 C (1.5 mb)
Secadores - BOOST R (1.5 mb)
Secadores - R 571 (1.5 mb)