Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Press these keys on the keypad: 1, 0, 0. The keypad backlight will go on and two tones will sound. Wait about 5 seconds; the keypad light will go off and then flash once. The unit is now switched back to Analog phone line and will stay in that setting the next time you turn the phone on. Using the Aura SoHo™ Conference Phone TO MAKE A CALL Press the Power Button .. to turn on the Aura SoHo™ Conference Phone, then enter the phone number for your call. ADJUST SPEAKER VOLUME Press the Volume Up ^ or Volume Down v button to adjust the speaker volume. ANSWER A CALL Press the Power Button .. when the Aura SoHo™ Conference Phone rings. END CALL Press the Power Button .. to end a call. REDIAL Press the REDIAL button to call the last number dialed. PLACE CALL ON HOLD Press the HOLD button to place a call on hold. The bottom indicator light near the Power Button .. will blink when on hold. Press the HOLD button again to resume the call. MICROPHONE MUTE Press the MUTE button to turn off the microphones in the Aura SoHo™ Conference Phone. The red indicator light above the MUTE button will be on when muted. While in MUTE mode, you will be able to hear the other end of the call, but they will not hear you. Press the MUTE button again to resume speaking to the caller(s). The red light will go out. CONFERENCE NOW The patented ConferenceNow™ button allows for you to press one button to connect with the Conferencing Service. FLASH The FLASH button is for three way conferencing. It allows you to put your first caller on hold while dialing the second number. Dial your first number normally. When the person is on the line, press the FLASH button and you will hear a second dial tone. Dial the second number. When that person is on the line, press the FLASH button again and all three of you will be on a conference call. 10 11 Reprogram Conference Number The Aura SoHo™ Conference Phone comes preprogrammed with the number for Spracht’s conferencing service provider. If you decide to use this service, all you have to do is press the CONF button to make a conference call. The Conference Center’s number is the factory default. If you already have your own conferencing service, you will have to reprogram the CONF button to the number of your service if you want to make one touch conference calls. In the reprogram mode, only the buttons with the outlines will be active. CONF- starts the programming process FLASH- will restore the factory default Conference Center Number MUTE- allows you to exit the process without saving HOLD- will save the new Conference Center Number and exit the program mode 0-9, *, #- allows you to enter the new Conference Center Number To reprogram the number, start with the Aura SoHo™ Conference Phone in “On Hook” (the phone is ready to receive calls). To place the Aura SoHo™ Conference Phone in reprogram mode, press and hold the CONF button for 10 seconds. After 5 seconds, the backlight will come on; when the backlight starts flashing, you may release the CONF button. Enter the new Conference Center Phone Number. The maximum number of digits you can enter is 16, the minimum is 3. This number will be stored in memory. Press the HOLD button, and the number will be stored. The next time that you press the CONF button, the number you entered will be dialed automatically. If you want to exit without saving the new number, press the MUTE button, and you will return to normal “On Hook”phone operation. If you ever want to return to the factory default number, press the FLASH button. Any custom number that was previously entered will be erased, and you will exit and return to normal “On Hook” phone operation. Exceptions: If you try to enter more than the maximum number of digits, the backlight will flash 4 times and no additional numbers will be accepted. There is a 5 minute built in timer for entering the new number. If the 5 minute limit is reached, the process will exit automatically and no data will be stored. The phone will return to normal “On Hook” operation. The FLASH button The FLASH button allows you to dial a number and when that party comes on the line, you can put them on “Hold” by pressing the FLASH button, and dial a second number. When the second party comes on the line, you press the FLASH button again to have both parties on the line for a three way conference call. There is a Region Code that must match the area of the world where you use the conference phone. The Region Code is preset at the factory. However, if your FLASH function doesn’t work as stated in the User Guide, please call your local Service Center or Spracht directly. A Customer Service representative will be able to advise you on how to modify this code, if necessary. Flash Button Programming INSTRUCTIONS FOR REPROGRAMMING THE FLASH BUTTON FOR INTERNATIONAL USE Where the Aura SoHo™ Conference Phone is “based” outside of North America Changing the region code is not recommended for end users. This procedure is either completed in Manufactin...
Este manual também é adequado para os modelos :Secadores - AURA SOHO CP-2016-003 (1.11 mb)
Secadores - AURA SOHO CP-2016-007 (1.11 mb)