Assessments - 4, GPA: 4
(
)
)
|
Facilidade de uso
Kit is available from an authorized parts distributor. 0” 0”1”0” (0 cm) (0 cm) (2.5 cm) (0 cm) 0” (0 cm) REAR CONSOLE MINIMUM INSTALLATION CLEARANCES - Inches (cm) SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm) 16” (40.5 cm) n/a UnderCounter n/a n/a n/a n/a Closet 0” (0 cm) 0” (0 cm) 16” (40.5 cm) 1” (2.5 cm) 0” 0”1” 0” (0 cm) (0 cm) (2.5 cm) (0 cm) 16” (40.5 cm) 7 Front Console Dimensions Rear Console Dimensions electrical supply on rear of unit, power cord length on gas unit 1” (2.5 cm) 13 1/2” (34.4 cm) 3 3/4” (9.5 cm) 36” (91.5 cm) 34 5/8” (87.9 cm) approximately 59” (150 cm) to center of rear vent gas supply pipe on center line height for rear vent under-counter installation height 2 9/16” rear of gas unit 2 9/16” rear of gas unit (6.5 cm) (6.5 cm) 3 3/4” 3 3/4” (9.5 cm) (9.5 cm) 27” (68.6 cm) 1” (2.5 cm) 13 1/2” (34.4 cm) 3 3/4” (9.5 cm) 36” (91.5 cm) 43 5/8” (111 cm) to center of rear vent gas supply pipe on center line height for rear vent electrical supply on rear of unit, power cord length on gas unit approximately 59” (150 cm) 4 3/8” (11 cm) 27” (68.6 cm) 47 1/2” (120.7 cm) to clear open door optional vent knockout 4 3/8” (11 cm) 47 1/2” (120.7 cm) to clear open door optional vent knockout Electrical installation The following are specifi c requirements for proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fi re hazard. - ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electrical shock and/or fi re hazard. Locate the dryer within reach of the receptacle for the length power cord to be purchased, allowing some slack in the cord. Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. - ELECTRICAL SHOCK HAZARD • A U.L.-approved strain relief must be installed onto power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. • Do not use an aluminum wired receptacle with a copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. Dryers operating on 208 volt power supply will have longer drying times than dryers operating on 240 volt power supply. 8 Grounding requirements - Electric dryer (USA) -ELECTRICAL SHOCK HAZARD -Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. After you purchase and install a 3 wire or 4 wire power supply cord having an equipment-grounding conductor and a grounding plug that matches you wiring system, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. DO NOT modify the plug you’ve installed on this appliance. For a permanently connected dryer: 1. The dryer MUST be connected to a grounded metal, permanent wiring system; or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Grounding requirements - Electric dryer (Canada) -ELECTRICAL SHOCK HAZARD -Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. For a grounded, cord-connected dryer: 1. The dryer MUST be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current. 2. Since your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. DO NOT modify the plug provided with the appliance. Grounding requirements - Gas dryer (USA and Canada) 1. The dryer is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. 2. The plug ...