Assessments - 4, GPA: 3
(
)
)
|
Facilidade de uso
TOOLS YOU WILL NEED Adjustable Crescent Wrench Putty Knife or Thin-Blade Screwdriver Phillips Head Screwdriver DOOR PARTS 3 - # 8 Screws (door asm and front panel) 8 - # 8 Screws (inner door, outer ring & hinge cover) Hinge Assembly Plastic Cover 6 - # 8 Machine Screws (inner door & hinge) 4 - # 8 Screws (strike plate) 7 - Beauty Buttons Hinge Cover STEP-BY-STEP INSTRUCTIONS Before You Start 1. Unplug the dryer from its electrical outlet. Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Remove Door Assembly 2. Open the door to approximately 130 degrees. 3. Remove the 2 screws starting from the bottom to the top. Make sure the door is supported while removing the screws. 4. Loosen the top screw as shown. Unhook the door by lifting and pulling. 5. Place the door on a soft protected flat surface so the inner door faces upward (door resting on handle side). Remove the 8 tapping screws located around the perimeter of the door outlining the gasket. Remove the 6 machine screws. Using a putty knife or any other flat tool, remove the 2 beauty buttons and install them on the opposite side. Remove Top Screw 8-#8 Tapping Screws 4 Beauty Buttons 6-# 8 Machine Tapping Screws Remove Hinge and Cover IMPORTANT: Note the location of the hinge (left or right) before removing. 6. With the screws removed, turn the door over and separate the outer door assembly and hinge cover of the door from the door frame and set aside. Outer Door Assembly Hinge Cover Hinge Assembly GEAppliances.com STEP-BY-STEP INSTRUCTIONS (cont.) Reinstall Hinge Assembly 7. Install the hinge assembly in the opposite side of the door as shown. Push the hinge assembly in place until the hinge holes align with the door holes. 8. Hold the hinge and door on their side with one hand and fasten the 6 machine screws as shown. Machine screws Reinstall Hinge Cover 9. Insert the hinge cover. Align the hinge cover holes with the holes in the door. 10. Secure the hinge cover with 2 taping screws. Hinge Cover Tapping Screws Reversing the door swing. STEP-BY-STEP INSTRUCTIONS (cont.) Outer Door Reassemble Door Assembly IMPORTANT: Make sure there is no dirt or any other foreign material in between the window panes. 11. Place the plastic outer door onto the inner door. Make sure that the handle part of the outer door is opposite the hinge as shown. 12. Turn the door over and fasten the outer door to the inner door using the 6 tapping screws. Inner Door Move Strike Bracket 13. Using a putty knife or any other flat tool, remove the 3 beauty buttons located on the dryer where the door will be installed and install them on the opposite side. 14. Switch the strike bracket and its cover to the opposite side by removing the screws. Reinstall both on the opposite side. Beauty Buttons Tapping Screws Partially Inserted Screw Reinstall Door Assembly 15. The door is now ready to be installed on the dryer. To ease this step, the hinge has keyholes that allow a partially fastened screw to be used as a hook. Partially fasten a screw to the uppermost screw hole. Hook the door on the partially fastened screw. Fasten the hinge by installing the other 2 screws and tightening the partially fastened screw above. Tighten All Screws Loading and using the dryer. GEAppliances.com Always follow the fabric manufacturer’s care label when laundering. Fabric Care Labels Below are fabric care label “symbols” that affect the clothing you will be laundering. WASH LABELS MachinewashcycleNormalPermanent Press/ wrinkle resistantGentle/ delicateHand washDo not washDo not wring Target Automatic Category Water Temperature Temperature Control Tap Cold Inlet Water Temperature Not used Cold 27°C/80°F Used Warm 40°C/105°F Used Hot 50°C/120°F Used Sanitize 70°C/160°F Used Front load target water temperature DRY LABELS TumbledryDryNormalPermanent Press/ wrinkle resistantGentle/ delicateDo not tumble dryDo not dry(used withdo not wash) HeatsettingHighMediumLowNo heat/air SpecialinstructionsLine dry/ hang to dryDrip dryDry atIn the shade BLEACH LABELS BleachsymbolsAny bleach(when needed) Only non-chlorine bleach(when needed) Do not bleach Sorting and Loading Hints As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items according to size. For example, do not dry a sheet with socks or other small items. Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. Do not overload. This wastes energy and causes wrinkling. Do not dry the following items: fiberglass items, woolens, rubber-coated items, plastics, items with plastic trim and foam-filled items. Loading and using the dryer. Always follow the fabric manufacturer’s care label when laundering. Care and Cleaning of the Dryer The Exterior: Wipe or dust any spills or washing compounds with a damp clo...