Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
Remove the shipping cap from gas pipe at the rear of the dryer. NOTE: DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician. b. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96 cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8 inch (1.27 cm to 0.96 cm) reducer for a connection. Apply an approved thread sealer that is resistant to the corrosive action of liquefied gases on all pipe connections. c. Open the shutoff valve in the gas supply line. d. Test all connections by brushing on a soapy water solution. NEVER TEST FOR GAS LEAKS WITH AN OPEN FLAME. 2. Connect the exhaust duct to outside exhaust system. Use duct tape to seal all joints. 3. With the dryer in its final position, adjust one or more of the legs until the dryer is resting solid on all four legs. Place a level on top of the dryer. THE DRYER MUST BE LEVEL AND RESTING SOLID ON ALL FOUR LEGS. 4. Plug the power cord into a grounded outlet. NOTE: Check to ensure the power is off at circuit breaker/fuse box before plugging the power cord into the outlet. 5. Turn on the power at the circuit breaker/fuse box. Before operating the dryer, make sure the dryer area is clear and free from combustible materials, gasoline, and other flammable vapors. Also see that nothing (such as boxes, clothing, etc.) obstructs the flow of combustion and ventilation air. 6. Run the dryer through a cycle check for proper operation. NOTE: On gas dryers, before the burner will light, it is necessary for the gas line to be bled of air. If the burner does not light within 45 seconds the first time the dryer is turned on, the safety switch will shut the burner off. If this happens, turn the timer to "OFF" and wait 5 minutes before making another attempt to light. 7. Place these instructions in a location near the dryer for future reference. NOTE: A wiring diagram is located inside the dryer. REPLACEMENT PARTS If replacement parts are needed for your dryer, contact the source where you purchased your dryer, or call Sears Parts and Service Toll Free Number 1-800-4-MY-HOME (1-800-469- 4663). Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children. The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. Lint Blade Retaining Pin Location and Orientation Install the pins after the lint blade is installed. TYPICAL 4 CONDUCTOR CORD TYPICAL 4 CONDUCTOR RECEPTACLE STRAIN RELIEF MOUNTING BRACKET NUT TIGHTEN NUT TO THESE THREADS POWER CORD RED WHITE BLACK TERMINAL BLOCK SILVER TERMINAL GREEN GROUND SCREW GREEN POWER CORD GROUND WIRE GREEN NEUTRAL GROUND WIRE ELECTRICAL CONNECTIONSFOR 4-WIRE SYSTEM GREEN POWER CORD TIGHTEN NUT TO THESE THREADS STRAIN RELIEF MOUNTING BRACKET GROUND SCREW NUT SILVER TERMINAL GREEN NEUTRAL GROUND WIRE ELECTRICAL CONNECTIONS FOR 3-WIRE SYSTEM ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. listed strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. Thread a U.L. listed 30 amp. power cord, NEMA 10-30 Type SRDT, through the strain relief. 4. Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely. 5. Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tighten both screws securely. Do not make a sharp bend or crimp wiring/ conductor at connections. 6. Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely. 7. Tighten the screws securing the cord restraint firmly against the power cord. 8. Tighten the strain relief nut securely so that the strain relief does not turn. 9. Reinstall the terminal block cover. ELECTRIC Dryer 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner. 2. Install a U.L. listed strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. Remove the green neutral ground wire from the green ground screw located above the terminal block. BLACK 240V WHITE NEUTRAL RED 240V...