Drying Rack (some models) lint screen opening. 4. 5. damage to the dryer. Common Drying Problems Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association. PROBLEM POSSIBLE CAUSES SOLUTIONS PREVENTIVE MEASURES Greasy, oily • Fabric softener sheet. • Rub fabric softener stains with bar soap. • Add a few bath towels to small l

E;A@ EB_5;8;_7 EGD >3 B>3CG7 E;9@3>_F;CG7 6G E^5:7j>;@97 -A;D >3 8;9GD7 B397 )7F;D7L FAGE >7E A4<7FE BD_E7@FE 63@E >7 F3?4AGD -_D;8;7L >34E7@57 67 6_9\FE 3BB3D7@FE EGD >7 E^5:7j>;@97 *;iHAGE 7@ FDAGH7L BD_H7@7L HAFD7 D7H7@67GD EEGK7L >;@F_D;7GD 6G F3?4AGD Z >3;67 6G@ 5:;88A@ :G?;67 *AG?7FF7L >3BB3D7;> Z G@ F7EF -A;D B397 *; >7 E^5:7>;@97 @7 8A@5F;A@@7 B3E D3?7@7L >7 BDA9D3??3F7GD EGD O&Q )7BADF7LjHAGE Z >3 E75F;A@ 67i6_B3@@397 B397 67EiBD_E7@F7E ;@EFDG5F;A@E 6GF;>;E3F;A@ 7F 6_F7D?;@7L >7

. . . . Internet: . . . Use and Care Manual IMPORTANT SAFETY INSTRUCTIONS . . . . . . 4 GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . 5 ABOUT YOUR DRYER . . . . . . . . . . . . . . . . . . . . . 6 GETTING TO KNOW YOUR DRYER . . . . . . . . . 6 ENERGY SAVING TIPS . . . . . . . . . . . . . . . . . . 7 OPERATING TIPS . . . . . . . . . . . . . . . . . . . . . . . 7 BEFORE USING FOR THE FIRST TIME . . . . . . 7 GETTING STARTED . . . . . . . . . . . . . . . . . . . . . . . 7 CYCLE SELECTION

The filter is cleaned when it no longer holds water. The filter must be dried thoroughly before being replaced. Le filtre devrait etre legerement frotte deux fois par an avec de l'eau savonneux chaud. Le filtre est nettoye quand il ne tient plus l'eau. Sechez bien le filtre avant de le remettre en place. El filtro debe ser restregado suavemente dos veces al ano con agua tibia enjabonada. El filtro debe ser limpiado cuando no es capaz de mantener el agua. Debera secarselo correctamente antes de v

1. Do not use plastic flexible duct to exhaust the dryer. Excessive lint can build up inside exhaust system and create a fire hazard and restrict air flow. Restricted air flow will increase drying time. If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or flexible metal duct. Ensure present duct is free of any lint prior to installing dryer duct. 2. The dryer must not be exhausted into any gas vent, chimney, wall, ceiling or any concealed space of a bu

Any floor unevenness should be corrected with leveling legs located on the bottom of the dryer. Tools and materials required • Phillips head and flathead screwdrivers • Channel-lock adjustable pilers • 1/2 inch open end wrench • Carpenter’s level • Measuring tape (12ft. min.) • Duct tap • Rigid or flexible metal 4 inch (102cm) duct • Vent hood Electrical requirements U.S. Only Power supply: 3 or 4 wire, 240 Volt, 30 Amp,60Hz, 1 Phase Power Supply Cord Kit (not supplied when sold in the United St

After installing your dryer in its final position, you can level your dryer. • Leveling legs can be adjusted by turning them clockwise to raise your dryer or by turning them counterclockwise to lower your dryer. Pausing or Restarting: • To pause the dryer at any time open the door or touch or press the start/pause button once. To restart, close door and touch or press start/pause button once. NOTE: Dryer will continue from where the cycle was interrupted, when door is closed within 5 minutes.

Items contaminated with cooking oil may contribute to a chemical reaction than could cause a load to catch fire. 16. If material has been used with any flammable liquids or solids, it should not used in the dryer until all traces of flammable liquids and its fumes have been removed. 17. This dryer must be properly installed in accordance with the installation instructions before it is used. See grounding instructions in the installations sections. 18. Proper grounding must be ensured to reduc

Good safe practice and caution must be applied when installing, operating and maintaining any appliances, after installing, if you are in doubt, call a certified electrician to install and wire the dryer. 12 English OPERATING INSTRUCTIONS Understanding the Control Panel Note: Features may vary per model. Start/Pause Button: (1) • Press the button to turn the dryer ON. Press this button once to start the dry process. Press this button once again to pause the activity during the dry cycle. Off But

Locate the dryer within reach of the receptacle for the length power cable to be purchased, allowing Some slack in the cord. Refer to the electrical requirements in this manual for The proper power cord to be purchased. 3. A UL approve strain relief must be installed onto power cable. If the the strain relief is not attached, the cord can be pulled out of the pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. 4. Do not use an aluminum wire receptac