4 Features.......................................... 5 Common Drying Problems .............. 5 Care and Cleaning ......................... 6 Avoid Service Checklist ................... 7 Warranty and Service (U.S.) ............ 8 Service (Canada) ............................ 9 Warranty (Canada) ....................... 10 Product Registration Thank you for choosing this dryer. This owner's guide will explain proper operation and care. Record Your Model and Serial Numbers Record below the model an

Connection of water inlet hose on Steam Models adds 3/4 in. (2 cm) to installation depth. Upward venting of exhaust on pedestal-mounted or freestandingfloor line floor line dryer mounted on optional pedestal 16.25” (41.5cm) 18.25” (46.5cm) 1.4” (3.5cm) 3.75” (9.5cm) 13.50” (34.5cm) to center of rear vent 3.40” (8.5cm) gas supply pipe on rear of gas unit centerline height for rear vent freestand dryer on floor * To obtain these minimal depth dimensions, dryer must either be vented straight back o

with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FORA3-WIRESYSTEM. Electrical requirements for gas dryer: CIRCUIT -Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY -2-wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current. POWER SUPPLY CORD -The dryer is equipped with a 120 volt 3-wire power cord. GROUNDING CONNECTION -See “Grounding requirements” in Electri

Momentarily turn on COLD supply and run some water into a bucket or container to clear any contaminants in the line. 4. Remove hose kit from dryer drum and inspect hose couplings for proper placement of rubber washers. 16 Installation Instructions Water connection, con’t (Steam Model only) WATER INLET ON DRYER DIRECT CONNECTION OR WITH EXTENSION COLD WATER SUPPLY HOSE TO WASHER If your installation has room for the COLD 1. watersupplytoacceptthe“Y”connectordirectly,threadthe“Y”connectortotheCOLD

HAND IRON), you should dry it in stages for best economy: Fill the drier and select the program HAND IRON; after the end of this program take out your laundry for ironing. Finally dry the remaining laundry with the program CUPBOARD DRY. • Only use the SPECIAL CARE button for loads up to 2.5kg. • Clean the fluff filter after every drying program! Description of the appliance Description of the appliance Front view Control panel Fluff filter Rating plate Feet Removable Plinth Reversible door (all

tion). Fine strainer not in place Install fine strainer and/or Loading door does not and/or large mesh filter not snap large mesh filter into close. locked in place. place. Problem Possible cause Remedy When pressing a but- Washing protection. After ton, the corresponding the start of the programme, Turn the programme knob to button flashes several the option can no longer be OFF. Set the programme again. times. set. Programme selector in OFF Turn programme selector to position. LIGHT or to any

Recommendation: Remove textiles immediately after drying. Special programme, lasting around 35 minutes, for refreshing or gently cleaning textiles with commercially available dry cleaning sets. REFRESH 1kg • • - (Only use those products which are declared as suitable for the drier by the manufacturer; please observe the manufacturer’s instructions for use.) 2) Press the SPECIAL CARE button! Drying Switching machine on / switching light on Turn the programme selector to any programme or turn it t

0 Open the door. 0 Press on the two tabs to unlatch and take off the removable plinth. 0 Turn the two securing disks through a quarter turn each outwards. 0 Pull the CONDENSER out of the base by the handle. 0 Clean the CONDENSER, best with a hand-held brush or by rinsing with a hand-held shower head. The water removal slits on the rear of the condenser must be free too. 1 Important! Do not use any sharply pointed objects to clean the CONDENSER. They could make it leak. 0 Reinsert and push in and

NOTE: The electrical service to the dryer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/ NFPA 70 or in Canada, CSA C22.1 Canadian Electrical Code Part 1. NOTE: The gas service to the dryer must conform with local codes and ordinances and the latest edition of the National Fuel Gas Code, ANSI Z223.1 or in Canada, CAN/CGA B149.1. NOTE: The dryer is designed under ANSI Z21.5.1 or ANSI/UL 2158 - CAN/ CSA C22.2 No. 112-97 (latest editions) f

7. Do not tamper with controls. 8. Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in the user-repair instructions that you understand and have skills to carry out. 9. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturers of the fabric softener or product. 10. Do not use heat to dry articles or products to eliminate static unless recommended by the manufacturers of the fabric softener or pro