Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
REMOVE THE THREE SCREWS SHOWN AND USEHAS A HALF INCH SQUARE HOLE IN IT.ASSEMBLY WITH THE ADAPTER BRACKET THAT1. REPLACE EXISTING BRACKET ON ADAPTER KITTOWORK ENGINE WELDER "# OPERATING INSRTUCTIONSCAPACITY FOR THE CURRENT AND THEN.A. WELDING CABLES MUST BE OF PROPERDUTY CYCLE OF IMMEDIATE AND FUTUREAPPLICATIONS. SEE OPERATING MANUALFOR PROPER SIZES.TO FEEDER "A" TERMINAL STRIP INN.B. IF ONLY ONE LN-23P IS USED, CONNECTADAPTER.DESIRED ELECTRODE POLARITY. POSITIONN.C. USE VOLTMETER SWITCH TO SELECTTHE SELECTOR SWITCH TO "WIRE WELDING K350-1 CV". 521 FEEDER "B" LN-23P ADAPTER KIT521 9 CONDUCTOR ADAPTER CABLE POSITION. LN-23PWIRE FEEDER "A" C TAKEN AS NOT TO DAMAGE ANYCONTROLLED" POSITION.NOT LIMITED TO ELECTRICALCOMPONENTS, WIRES OR FUEL TANKS. WARNING F-10 F-10 DIAGRAMS CONNECTION DIAGRAM: % & "#$ ' 7 479 7,+0/9+ ?39: ,/4+52 7,+4B+A70+ 2+083634-326744+69 % " & 7 479 97.6: +5+69036/55@ 538+ ,/092 $! S23991A & (34- ,/092++, -./012 34 ,5/6+70 2+0836+ 9:32 +;.3,<+49 WARNING $! "#$ COMMANDER 300 F-11 F-11 DIAGRAMS CONNECTION DIAGRAM: 326744+69 % " & 7 479 97.6: +5+69036/55@ 538+ ,/092 B+A70+ 2+083634-7 479 7,+0/9+ ?39: ,/4+52 7,+4 = ++, -./012 34 ,5/6+++, /?/@ A07< <7834- ,/092 WARNING 45@ ;./53A3+1 ,+02744+5 2:7.51 3429/55(.2+70 2+0836+ 9:32 +;.3,<+49 " $)$ % & % " & & & & % % % " & " * % AS23992 COMMANDER 300 F-12 F-12 DIAGRAMS CONNECTION DIAGRAM: or service this equipment. Only qualified personnel should install, use Keep away from moving parts. Keep guards in place. MOVING PARTS can injure WARNINGDo not touch electrically live parts. before servicing. Disconnect NEGATIVE (- ) Battery lead Do not operate with panels open. ELECTRIC SHOCK can kill 14 PINAMPHENOL TO WORK + _ ENGINE WELDERS / LN- 25 WITH K624- 1 42 VOLT REMOTE OUTPUT CONTROL MODULE CONNECTION DIAGRAM S24787-310-27-2000 TO LN-25 INPUTCABLE PLUG ELECTRODE CABLETO WIRE FEED UNITCAUTION:ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING CAUSEAN INCREASE IN THE AC WIRE FEEDER VOLTAGE, WHICH SETAT THE FACTORY – DO NOT ADJUST ABOVE RPM SPECIFICATIONS N.A. PLACE THE MODE SWITCH IN THE “CV-WIRE” POSITION. REMOTELYCONTROLLED” POSITION. N.B. CONNECT WELDING CABLES TO OUTPUT STUDS TOMATCH THE POLARITY OF THE ELECTRODE N.C. WELDING CABLES MUST BE OF PROPER FUTUREAPPLICATIONS. SEE OPERATING MANUAL. N.D. PLACE IDLER SWITCH IN “AUTO” K626- XX INPUT CABLE ASSEMBLY COMMANDER 300 F-13 F-13 DIAGRAMS CONNECTION DIAGRAM: " "#$ S23994A & (0 2+0836+ 9:32 +;.3,<+49++, /?/@ A07< <7834- ,/092++, -./012 34 ,5/6+326744+69 % " & 7 479 97.6: +5+69036/55@ 538+ ,/0927 479 7,+0/9+ ?39: ,/4+52 7,+4 WARNING COMMANDER 300 COMMANDER 300 / K930 TIG MODULE / CONNECTION DIAGRAM . . . WARNING F-14 CONNECTION DIAGRAM: 7 479 7,+0/9+ ?39: ,/4+52 7,+4326744+69 % " & B+A70+ 2+083634-7 479 97.6: +5+69036/55@ 538+ ,/092 . ++, -./012 34 ,5/6+++, /?/@ A07< <7834- ,/09245@ ;./53A3+1 ,+02744+5 2:7.51 3429/55(.2+70 2+0836+ 9:32 +;.3,<+49 . F-14DIAGRAMS . . & . )'" . = COMMANDER 300 )'" " " ! " " & & % % . > & % % % %( & . % " & " * % . . & & & % % & . & . A S24062 F-15 F-15 DIAGRAMS CONNECTION DIAGRAM: 7 479 7,+0/9+ ?39: ,/4+52 7,+4B+A70+ 2+083634-326744+69 % " & 7 479 97.6: +5+69036/55@ 538+ ,/092 = D $)!" #% & & % % ++, -./012 34 ,5/6+++, /?/@ A07< <7834- ,/092 WARNING 45@ ;./53A3+1 ,+02744+5 2:7.51 3429/55(.2+70 2+0836+ 9:32 +;.3,<+49 "!# "!# $)# % & AS24609 COMMANDER 300 F-16 DIAGRAMS F-16 COMMANDER 300 DIMENSION PRINT * TRAILER MOUNTING HOLE LOCATIONS. 45.67 * 42.00 * * 6.55 22.25 8.69 6.53 24.97 6.56 BOTTOM VIEW OF WELDER BASE. 30.25 32.08 38.58 50.85 GRAVITY WITH OIL IN ENGINE AND FULL FUEL TANK. CENTER OF FOR BATTERY REMOVAL. 31.50 14.63 * 37.30 45.38 19.63 28.99 23.69 50.38 1.26 54.44 63.10 M18962 B-RW NOTES COMMANDER 300 NOTES COMMANDER 300 Now Available...12th Edition The Procedure Handbook of Arc Welding With over 500,000 copies of previous editions published since 1933, the Procedure Handbook is considered by many to be the “Bible” of the arc welding industry. This printing will go fast so don’t delay. Place your order now using the coupon below. The hardbound book contains over 750 pages of welding information, techniques and procedures. Much of this material has never been included in any other book. A must for all welders, supervisors, engineers and...