Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
To initiate a weld, the course and fine output control knobs must be set for the desired current. The tungsten electrode is then scratch on the work which establishes the arc. To stop the arc, simply lift the TIG torch away from the work piece. The tungsten may then be scratched on the work piece to restrike the arc. If a high frequency start is desired, the K930-2 TIG Module can be used with the EAGLE™ 10,000 Plus. The settings are referenced. The EAGLE™ 10,000 Plus and any high frequency generating equipment must be properly grounded. See the K930-2 TIG Module operating manuals for complete instructions on installation, operation and maintenance. When using the TIG Module, the OUTPUT control on the EAGLE™ 10,000 Plus is used to set the maximum range of the CURRENT CONTROL on the TIG Module or an Amptrol if connected to the TIG Module. RANGE SETTING TYPICAL ELECTRODE SIZE CURRENT RANGE 90 MAX. 3/32 40 TO 90 AMPS 145 MAX. 1/8 70 TO 145 AMPS 225 MAX. 5/32 120 TO 225 AMPS TYPICAL CURRENT RANGES (1) FOR TUNGSTEN ELECTRODES(2) Tungsten Electrode Diameter in. (mm) DDENE (-) DAZE (+) Approximate Argon Gas Flow Flow Rate C.F.H. ( l /min.) TIG TORCH Nozzle Size (4), (5) 1%, 2% Thoriated Tungsten 1%, 2% Thoriated Tungsten Aluminum Stainless Steel .010 (.25) 2-15 (3) 3-8 (2-4) 3-8 (2-4) #4, #5, #6 0.020 (.50) 5-20 (3) 5-10 (3-5) 5-10 (3-5) 0.040 (1.0) 15-80 (3) 5-10 (3-5) 5-10 (3-5) 1/1e (1.6) 70-150 10-20 5-10 (3-5) 9-13 (4-6) #5, #6 3/32 (2.4) 150-250 15-30 13-17 (6-8) 11-15 (5-7) #6, #7, #8 1/8 (3.2) 250-400 25-40 15-23 (7-11) 11-15 (5-7) 5/32 (4.0) 400-500 40-55 21-25 (10-12) 13-17 (6-8) #8, #10 3/16 (4.8) 500-750 55-80 23-27 (11-13) 18-22 (8-10) 1/4 (6.4) 750-1000 80-125 28-32 (13-15) 23-27 (11-13) (1) When used with argon gas. The current ranges shown must be reduced when using argon/helium or pure helium shielding gases. (2) Tungsten electrodes are classified as follows by the American Welding Society (AWS): Pure EWP 1% Thoriated EWTh-1 2% Thoriated EWTh-2 Though not yet recognized by the AWS, Ceriated Tungsten is now widely accepted as a substitute for 2% Thoriated Tungsten in AC and DC applications. (3) DAZE is not commonly used in these sizes. (4) TIG torch nozzle "sizes" are in multiples of 1/16ths of an inch: # 4 = 1/4 in. (6 mm) # 5 = 5/16 in. (8 mm) # 6 = 3/8 in. (10 mm) # 7 = 7/16 in. (11 mm) # 8 = 1/2 in. (12.5 mm) #10 = 5/8 in. (16 mm) (5) TIG torch nozzles are typically made from alumina ceramic. Special applications may require lava nozzles, which are less prone to breakage, but cannot withstand high temperatures and high duty cycles. EAGLE™ 10,000 PLUS B-5 OPERATION B-5 ARC GOUGING The EAGLE™ 10,000 Plus can be used for limited arc gouging. Set the Range switch to adjust output current to the desired level for the gouging electrode being used according to the ratings in the following table: ELECTRODE SETTING CURRENT RANGE (DC, electrode positive) 1/8 30 - 60 Amps 5/32 90 - 150 Amps 3/16 150 - 250 Amps SUMMARY OF WELDING PROCESSES PROCESS CONTROL CABLE USED IDLE MODE ELECTRODE WHEN NOT WELDING TO START WELDING STICK No AUTO Hot Touch electrode to work. Welding starts immediately And engine goes to high Idle. TIG, TIG MODULE WITH WITH CONTACTOR KIT CONTROL CABLE, & AMPTROL Yes HIGH Cold Press Amptrol, Contactor closes, Welding starts immediately. EAGLE™ 10,000 PLUS C-1 ACCESSORIES C-1 OPTIONAL EQUIPMENT (Field Installed) K2635-1 SMALL TWO-WHEEL ROAD TRAILER WITH DUO-HITCH-For heavy-duty road, off-road, plant and yard use. Includes pivoting jack stand, safety chains, and 13" wheels. Overall width 60". Stiff .120" welded rectangular steel tube frame construction is phosphate etched and powder coat painted for superior rust and corrosion resistance. Low sway suspension gives outstanding stability with manageable tongue weight. Wheels bearings are packed with high viscosity, high pressure, low washout luxuriates® grease. Features a Duo-Hitch™ - a 2" Ball/Lunette Eye combination hitch. Order: K2635-1 Trailer K2639-1 Fender and Light Kit K2640-1 Cable Rack K1737-1 FOUR WHEEL ALL-TERRAIN UNDERCARRIAGE - For moving by hand at construction sites. Heavy duty puncture resistant pneumatic tires. K1770-1 UNDERCARRIAGE (FACTORY) - For moving by hand on a smooth surface. One or two gas cylinders can be mounted on the rear of the undercarriage with the installation of K1745-1 Cylinder Holder(s). Heavy duty puncture resistant pneumatic tires and front caster. K1745-1 WELDING GAS CYLINDER LOX TANK HOLDER Holds Welding Gas Cylinder for use on K1770-1 Undercarriage. One or two may be installed on an undercarriage. K1788-1 ROLL CAGE - Gives added damage protection. Attaches to K1737-1, K1770-1, and K957-1. K886-2 Canvas Cover -To protect the EAGLE™ 10,000 Plus when not in use. Made from attractive red canvas material which is flame retardant, mildew resistant, and water repellent. K802R Power Plug Kit - provides four 120V plugs ...