Assessments - , GPA:
(
)
)
Fabricante : Hobart
Arquivo Tamanho: 1.25 mb
Arquivo Nome : o278n_hob.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
Veuillez consulter votre medecin pour obtenir plus de details. OM-278 Page 8 OM-278 Page 9 SECTION 2 – DEFINITIONS 2-1. General Precautionary Label Warning! Watch Out! There are possible hazards as shown by the symbols. 1 Electric shock from welding electrode or wiring can kill. 1.1 Wear dry insulating gloves. Do not touch electrode with bare hand. Do not wear wet or damaged gloves. 1.2 Protect yourself from electric shock by insulating yourself from work and ground. 1.3 Disconnect input plug or power before working on machine. 2 Breathing welding fumes can be hazardous to your health. 2.1 Keep your head out of the fumes. 2.2 Use forced ventilation or local exhaust to remove the fumes. 2.3 Use ventilating fan to remove fumes. 3 Welding sparks can cause explosion or fire. 3.1 Keep flammables away from welding. Do not weld near flammables. 3.2 Welding sparks can cause fires. Have a fire extinguisher nearby, and have a watchperson ready to use it. 3.3 Do not weld on drums or any closed containers. 4 Arc rays can burn eyes and injure skin. 4.1 Wear hat and safety glasses. Use ear protection and button shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection. 5 Become trained and read the instructions before working on the machine or welding. 6 Do not remove or paint over (cover) the label. 1/96 S-176 254-A 1 1.1 1.2 1.3 3 3.1 3.2 3.3 4 4.1 + 2 2.1 2.2 + + 5 6 + 2.3 2-2. Input Connection Label 1 Warning! Watch Out! There are possible hazards as shown by the symbols. 2 Electric shock from wiring can kill. 3 Disconnect input plug or power before working on machine. 4 Read the Owner’s Manual before working on this machine. 5 Consult rating label for input power requirements, and check power available at the job site – they must match. 6 Read Owner’s Manual and inside labels for connection points and procedures. 7 Move jumper links as shown on inside label to match voltage at job site. 8 Having a loop of extra length, connect grounding conductor first. 9 Connect line input conductors as shown on inside label – double-check all connections, jumper link positions, and input voltage before applying power. S-179 290 1 4 5IIIIIIIIIIII3 IIII2 ? V ? A ? V 3 1/96 1 2 3 4 5 6 87 9 2-3. Electric Shock And Airflow Label S-179 563 1 Warning! Watch Out! There are possible hazards as shown by the symbols. 2 Electric shock from wiring and exposed weld terminals can kill. 3 Close door before turning on unit. 1 2 3 1/96 2-4. Nameplate Safety Symbols 1 1 1 Warning! Watch Out! There are possible hazards as shown by the symbols. 2 Electric shock from welding electrode or wiring can kill. 3 Sparks from arcing electrode can cause explosion or fire – disconnect cable for process not in use. 4 Read Owner’s Manual for connection procedures. 2 3 4 5 6 5 6 Electric shock from wiring can kill. Disconnect input power before working on unit or making terminal strip connections. Nameplate D-179 389 OM-278 Page 10 2-5. Manufacturer’s Rating Label For CE Products S-174 343 For label location see Section 3-4. OM-278 Page 11 2-6. Symbols And Definitions Some symbols are found only on CE products.NOTE A Amperes Amperage/Voltage Control–Panel Gas Tungsten Arc Welding (GTAW) Shielded Metal Arc Welding (SMAW) Temperature Wire Feeder Arc Force (DIG) Gas Metal Arc Welding (GMAW) Output Circuit Breaker Remote V Volts Positive High Inductance Weld Output Terminal Positive Low Inductance Weld Output Terminal Negative Weld Output Terminal Input On Off Percent Direct Current U0 Rated No Load Voltage (Average) U1 Primary Voltage U2 Conventional Load Voltage Line Connection I1 Primary Current I2 Rated Welding Current X Duty Cycle Three-Phase Transformer Rectifier IP Degree Of Protection Three-Phase S1 KVA Hz Hertz S Suitable For Areas Of Increased Shock Hazard Protective Earth (Ground) SECTION 3 – INSTALLATION 3-1. Specifications Model IP IPIP Rating Rated Welding Output Amperage/ Voltage Range DC Max MaxMax OCV–DC Amperes Input at Rated Load Output, 50 or 60 Hz, Three-Phase 230 V 380 V 400 V 440 V 460 V 520 V 575 V KVA KW 650 650650 Amp 21M 650 A @ 44 V VV olts DC, olts DC,olts DC, 100% Duty Cycle 50 – 815 A In CC Mode 72 (70) VDC In CC Mode 126 3.8* 3.8*3.8* 77 1.9* 1.9*1.9* 73 1.8* 1.8*1.8* 66 1.6* 1.6*1.6* 63 1.9* 1.9*1.9* 54 1.1* 1.1*1.1* 50.4 1.4* 1.4*1.4* 50 1.52* 1.52*1.52* 34.8 0.76* 0.76*0.76* 10 – 65 V In CV Mode 70 (66) VDC In CV Mode *While idling ( ) Indicates specification differences for CE models OM-278 Page 12 OM-278 Page 13 3-2. Duty Cycle And Overheating Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, thermostat(s) opens, output stops, and cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or duty cycle before welding. Exceeding duty cycle can damage unit and void warranty. 100% Duty Cycle Overheating 0 15 A/V OR Minutes Reduce Duty Cycle duty1 4/95 / Ref. SA-168 918 Continuous Welding 3-3. Volt-Ampere Curves Volt-ampere c...