Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
Only use the abrasive wheel approved for the type of material to be cut. There are different abrasive wheels, each specially marked. For example: TS 400 English / USA 1. Stone Also can be used for concrete, masonry, reinforced concrete and brick cutting. 2. Steel Can be used for all ferrous metal cutting. 3. Asphalt Also can be used for aggregate concrete cutting. 4. Ductile iron Also can be used for certain grades of cast iron (SG 17-24), bronze and copper cutting. For cutting composite materials please ask your STIHL dealer. Diamond Abrasive Wheels Diamond abrasive wheels have a much better cutting performance than composite abrasive wheels. The diamond wheels are steel centered, and diamond particles are imbedded in their cutting edges. They can be used for concrete, asphalt, natural stone, clay pipe, brick and the like. They are not normally suitable for cutting metal or other materials. Wet or dry cutting is possible. With wet cutting your diamond wheel will have a longer life. Water attachments are included with your STIHL cut-off machine. See the appropriate section of your instruction manual. ! Warning! Do not remount a used diamond abrasive wheel without first inspecting for under-cutting, flatness, core fatigue, segment damage or loss, signs of overheating (discoloration) and possible arbor hole damage. Check the wheel for cracks and make sure that no pieces have broken off the wheel before use. Always fit the wheel so that the arrow on the wheel points in the direction of the rotation of the spindle. THE USE OF THE CUT- OFF MACHINE Transporting the STIHL Cutquik ! Warning! Always stop the engine before putting a cut-off machine down or carrying it. The abrasive wheel continues to rotate for a short while after the throttle trigger is released (flywheel effect). Carrying a cut-off machine with the engine running is extremely dangerous. Accidental acceleration of the engine can cause the wheel to rotate. Avoid touching the hot muffler. By hand: When carrying your cut-off machine by hand, the engine must be stopped and the cut-off machine must be in the proper position. Grip the front handle and place the muffler at the side away from the body. ! Warning! Always protect the cutting wheel from hitting the ground or any other objects. Damaged wheels may shatter and cause serious or fatal injury. TS 400 English / USA By vehicle: Properly secure your cut-off machine to prevent turnover, fuel spillage and damage to the cut-off machine. Never transport with cutting wheel mounted. A wheel damaged during transportation may shatter during operation and cause serious personal injury. Preparation for the Use of the Cut-Off Machine For assembly, follow the procedure described in the appropriate section of your instruction manual. Keep the handles dry, clean and free of oil and fuel. ! Warning! Before operation of your cut-off machine, be sure the controls (e.g. throttle trigger, stop switch) and the safety devices are working properly, the carburetor idle and maximum speed are correctly adjusted, the wheel is properly mounted, and the wheel guard is in place and securely fastened to your unit. All wheels should be carefully inspected for good condition before mounting. Adjust the wheel guard so that sparks, dust and cut material are deflected away from the operator, and cannot reach flammable surroundings. See section “Operating Instructions“ of your instruction manual. Never operate a cut-off machine that is damaged, improperly adjusted or not completely and securely assembled. Inspect for safety in operation. Proper tension of the V- belt is important. In order to avoid an incorrect setting, the tensioning procedure must be followed as described in your manual. Always make sure the hexagonal collar nuts for the cast arm are tightened securely. Check V-belt tension after one hour of operation and correct if necessary. Fuel Your STIHL power tool uses an oil- gasoline mixture for fuel (see the chapter on “Fuel” of your instruction manual). ! Warning! Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and serious burn injury or property damage. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape from the fuel system. Fueling Instructions ! Warning! Fuel your power tool in well-ventilated areas, outdoors. Always shut off the engine and allow it to cool before refueling. Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used, the weather conditions and the tank venting system. In order to reduce the risk of burns and other personal injury from escaping gas vapor and fumes, remove the fuel filler cap on your power tool carefully so as to allow any pressure build-up in the tank to release slowly. Never remove the fuel filler cap while the engine is running. TS 400 English / USA Select bare ground for f...
Este manual também é adequado para os modelos :Máquinas de soldar - TS 400 (3.12 mb)
Máquinas de soldar - TS 400 (3.12 mb)
Máquinas de soldar - TS 400 (3.12 mb)