Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
After cooling down completely, disconnect AC Power Cord. TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. Power off? Message disappears after 4 seconds. When “Power Management” function is ON, the projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power management” on page 36. When WARNING TEMP. Indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning on projector again. When WARNING TEMP. Indicator continues to flash, follow the procedures below: 1. Press POWER ON-OFF button to turn the projector off and disconnect AC Power Cord from an AC outlet. 2. Check Air Filters for dust accumulation. 3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 40.) 4. Turn the projector on again. If WARNING TEMP. Indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center. BASIC OPERATION ADJUSTING SCREEN ZOOM ADJUSTMENT 1 1 Press ZOOM button on Top Control or ZOOM / button on 2 2 Remote Control Unit. The message “Zoom” is displayed. Press ZOOM button or POINT UP button to make image larger, and press ZOOM button or POINT DOWN button to make image smaller. Zoom Message disappears after 4 seconds. FOCUS ADJUSTMENT 1 1 Press FOCUS button on Top Control or FOCUS / button on 2 2 Remote Control Unit. The message “Focus” is displayed. Adjust focus of image by pressing FOCUS / button or POINT UP/DOWN button(s) . Focus Message disappears after 4 seconds. KEYSTONE ADJUSTMENT If a projected picture has keystone distortion, correct the image with KEYSTONE adjustment. 1 1 Press KEYSTONE button on Remote Control Unit or select Keystone on SETTING menu. (Refer to page 35.) Keystone dialog box appears. 2 2 Correct keystone distortion by pressing POINT UP/DOWN/LEFT/RIGHT button(s). Press POINT UP button to • Arrows are white in no correction. reduce the upper part of the image, and press POINT DOWN • Arrow(s) of direction being corrected turn(s) red. button to reduce the lower part. Press POINT LEFT button to • Arrow(s) disappear(s) at the maximum reduce the left part, and press POINT RIGHT button to reduce correction. the right part. Reduce the upper width Reduce the lower width Reduce the left part with Reduce the right part with with POINT UP button. with POINT DOWN button. POINT LEFT button. POINT RIGHT button. PICTURE FREEZE FUNCTION Press FREEZE button on Remote Control Unit to freeze the picture on-screen. To cancel FREEZE function, press FREEZE button again or press any other button. BASIC OPERATION NO SHOW FUNCTION Press NO SHOW button on Remote Control Unit to black out the image. To restore to normal, press NO SHOW button again or press any other button. No show Message disappears after 4 seconds. P-TIMER FUNCTION Press P-TIMER button on Remote Control Unit. The timer display “00 : 00” appears on the screen and the timer starts to count time (00 : 00 ~ 59 : 59). To stop P-TIMER display, press P-TIMER button. And then, press PTIMER button again to cancel P-TIMER function. SOUND ADJUSTMENT Indicates approximate DIRECT OPERATION level of volume. Volume Press VOLUME (+/–) button(s) on Top Control or on Remote Control Unit to adjust volume. Volume dialog box appears on the screen for a few seconds. (+) button to increase volume, and (–) button for decreasing. Mute Press MUTE button on Remote Control Unit to cut off sound. To restore sound to its previous level, press MUTE button again or press Volume (+/–) button(s). MENU OPERATION 1 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SOUND Menu icon. 2 2 Press POINT DOWN button to move a red frame pointer to the item that you want to select, and then press SELECT button. Volume To increase volume, press POINT RIGHT button, and press POINT LEFT button to decrease volume. Press MUTE button to set Mute function On or Off. The display disappears after 4 seconds. SOUND MENU Indicates approximate level of volume. SOUND Menu icon Close SOUND Menu. Mute Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box display is changed to “On” and sound is cut off. To restore sound to its previous level, press POINT LEFT/RIGHT button(s) again. COMPUTER INPUT SELECTING INPUT SOURCE INPUT button DIRECT OPERATION Choose Computer by pressing INPUT button on Top Control or on Remote Control Unit. If projector cannot reproduce proper image, select correct input source through MENU OPERATION (see below). Computer Video INPUT MENU MENU OPERATION 1 1 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to INPUT Menu icon. 2 2 Press POINT DOWN button to move a red arrow pointer to Computer and then press SELECT button. Source Select Menu will appear. 3 3 Move a pointer to either RGB (Digital) or RGB (Analog) and then press SELECT button. When digital signal is con...
Este manual também é adequado para os modelos :TV - LC-NB4S (640.12 kb)