Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Do not over-tighten these bolts and do not release the mount until all bolts are in place. 8 Once all (4) lag bolts are in place you must tighten each one. (note: be sure not to over tighten). 1 1 3. Mounting the wall plate (concrete) B Warning For safety reasons,the concrete wall must be capable of supporting the combined weight of the mount and display. 1 See enclosed mounting template for diagram and use enclosed mounting template as a guide for precision mounting. 2 Using the enclosed mounting template, place the diagram against the wall and mark four locations on the wall where the mount is to be Installed. 3 With the help of another person, place the mount against the wall and level it using the bubble guide. 4 While another person holds the mount in place, mark four locations on the wall where the mount is to be installed. 5 Set the mount aside and drill a 3/8” (10 mm) pilot hole at each marked location. Remove any excess dust from the holes. 6 Insert a Concrete Anchor (P) into each hole so that it is flush with the concrete surface.A hammer can be used to lightly tap the anchors into place if necessary. 7 Place the mount back against the wall and secure it using the lag bolts (Q) and lag bolt washers (R) provided. Do not over-tighten these bolts and do not release the mount until all bolts are in place. 8 Once all (4) lag bolts are in place you must tighten each one. Be sure not to over tighten. 2 2 D Note Iftheconcretewalliscoveredbyalayerofplasterordrywall, theconcreteanchormustpasscompletelythroughthelayertorest flush with the concrete surface. 3.3 Attaching the arms to the display B Warning Use extra care during this part of the installation. If possible, avoid placing your display facedown as it may damage the viewing surface. D Note Your mount comes with a selection of bolt diameters and lengths to accommodate a wide variety of display models. Not all of the hardware in the kit will be used. 1 Determine the correct length of bolt to use with your display by first examining the back of your display. A. If your display has a flat back: You will use one of the shorter bolts (A, D, G, or J) from the hardware kit. 3 3 B.Ifyourdisplayhasacurvedorrecessedback:You will use one of the longer bolts (B, E, H, or K) along with a spacer (M or N). 4 4 securethearmintopositionORapadlock(notincluded)canbeinsertedintooneofthetabstohelppreventtheftofyourdisplay.7 7 3 The cable management clips can be used to 7 7 3 The cable management clips can be used to 5 6 2 Determine the correct diameter of bolt to use by carefully trying one bolt each from Bags 1 -4 of the hardware kit. Do not force any of the bolts – if you feel resistance stop immediately and try a smaller diameter bolt. 3 Attach the arms to the back of your display using the bolts identified in Steps 1 and 2 along with the corresponding Lock Washer (C, F, I, or L). 5 4 Mounting and adjusting 1 With the help of another person, carefully lift your display and place it on mount. Place the display in the middle of the mount, and do not release the display until the mounting arms have securely hooked onto the crossbars. 6 A) If you are using the M4, M5, or M6 bolts (Bags 1, 2, and 3 respectively), you will also need to use the M6 Washers (O). B) If you are using one of the longer bolts on a display with a curved or recessed back, you will also use a spacer (M or N). Use the smaller spacer (M) for M4 and M5 bolts and the large spacer (N) for M6 and M8 bolts. Make sure all screws are secure, but do not over-tighten them. E Tip Use a longer bolt and spacer for displays with curved or recessed backs.Do not use the M6Washer (O) if you are using the M8 Bolts (J or K). 2 Move the safety tab located on each arm into position to avoid having the display accidentally lifted from the mount.This MUST be done in order to secure the display to the mount. D Note A cotter pin (included) is used to keep your power cord and other cables in order. 4 Side-to-side and front-to-back adjustments can be made by firmly grasping your display and carefully moving it to the desired position. 9 10 9 10 If any of the arms become too lose to hold their position, they can be tightened using the alley key provided in your hardware kit. 8 8 To adjust the tilt position of your display, have one person hold the display in place while another person loosens the two tilt adjustment knobs located on either side of the mount. Once the knobs are loose, move the display to the desired angle. Tighten the knobs securely before releasing the display. 9 If you find that your display is not level, first loosen the horizontal adjustment screw located behind the mount using the allen key provided in your hardware kit. Carefully level your display and re-tighten the adjustment screw. 10 5 Guarantee and service Please contact Philips directly if you have any questions in the installation process of the wall mount. Call 1-919-573-7854. Limited Two-Year Warranty Philips warrants that this product shall be free...