Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
If you are having technical problems, please call our accessory support help line at 919-573-7854 before returning the product to the store, (please see page 5 of this instruction manual for details “Before You Start”). What’s in the box RG59 Coaxial cable Power transformer Instructions for use PHILIPS Antenna Matching transformer r © Connect Connect coaxial cable to antenna 1 Connect supplied coaxial cable to the back of the antenna. 2 Connect the coaxial cable from your cable or satellite source to the back of the antenna to the connector labeled IN FROM CABLE Connect coaxial cable to TV Connect the supplied coaxial cable from the antenna to the back of your TV using one of the two methods illustrated*. Connect power Connect the power transformer to the antenna then to AC power outlet. “If you have scrcw connections on your TV, attach the cable to the matching transformer and then to your TV. You will need a band separator (not included) to access UHF reception. If you have a 75 ohm jack and a set of UHF scrcw connectors on your TV. attach a coax cable to the 75 ohm jack. You will need a band separator (not included) to access UHF reception. 3 Install Suggested starting point Locate signal source Face the antenna towards the source of the signal (transmitter). For help locating the signal source go to ForVHF reception, position the dipoles as shown** For channels 2 through 6. extend the dipoles fully and adjust to a horizontal position**. For channels 7 through 13, shorten the dipoles by 1/3 length and position them in a“V”** For FM reception, position the dipoles as shown** For FM reception, extend the dipoles to 30” and position them either straight up or horizontally**. **For best results, some additional adjustments may be necessary. Install Before ^or t^'s antenna to work properly, you must access the menu Y on the television you are connecting this antenna to (consult T°u y0ur te|evision owner’s manual) then set it to receive the Start signal from an ANTENNA instead of CABLE or SATELLITE. For UHF reception, position the dipoles as shown** For channels 14 through 69. rotate and/or tilt the center loop towards the transmitter. Using the selector switch Choose your signal source by switching from ANTENNA to CABLE. Note that in the CABLE position. 1 LED lamp will illuminate. Fine-tune the picture Slowly increase the gain until you achieve the clearest picture possible. Rarely, it is necessary to use the maximum gain.Too much gain may result in poor picture quality. Limited lifetime warranty Philips warrants chat this product shall be free from defects in material, workmanship and assembly, under normal use. in accordance with the specifications and warnings, for as long as you own this product-This warranty extends only to the original purchaser of the product, and is not transferable.To exercise your rights under this warranty, you must provide proof of purchase in the form of an original sales receipt that shows the product name and the date of purchase. For customer support or to obtain warranty service, please call 919-S73-78S4.THERE ARE NO OTHER EXPRESS OR IMPLIED WARRANTIES. Philips’ liability is limited to repair or. at its sole option, replacement of the product. Incidental, special and consequential damages are disclaimed where permitted by law.This warranty gives you specific legal rights.You may also have other rights that vary from state to state. f Indice de contenido 6 Qué contiene la caja 7 Conectar 7 Conectar el cable coaxial a la antena 7 Conectar el cable coaxial a la TV 7 Conectar la corriente 8 Instalar 8 Localizar una fuente de señal 8 Para la recepción VHF 8 Para la recepción FM 9 Para la recepción UHF 9 Uso del conmutador selector 9 Sintonice la imagen 9 Garantía limitada de por vida Philips fabrica productos de la mejor calidad. Si tiene algún proble-ma técnico, llame a nuestra linea de ayuda de asistencia para acce-| sorios al 919-573-7854 antes de devolver el producto al establec-ttlÉBp ¡miento. (Consulte la página 9 de este manual de instrucciones para obtener información 'Antes de comenzar"). Qué contiene la caja Cable coaxial RG59 Transformador de adaptación de manejo Transformador de corriente Connectar Conectar el cable coaxial a la antena 1 Conectar el cable coaxial suministrado en la parte trasera de la antena 2 Conectar el cable coaxial de su fuente de cable o satélite en la parte trasera de la antena, en el conector que indica IN FROM CABLE. Conectar el cable coaxial a la TV Conectar el cable coaxial suministrado desde la antena hasta la parte trasera del aparato de TV mediante uno de los dos métodos ilustrados*. Conectar la corriente Conectar el transformador de corriente desde la antena a una salida de corriente AC. * Si tiene conexiones para atornillar en su TV. conecte el cable en el transformador de adaptación y posteriormente en su TV Para acceder a la recepción UHF nec...
Este manual também é adequado para os modelos :receptor e amplificador - US2-MANT510 (1.04 mb)