Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
CHAPTER TWO: INSTALLATION 2.8 Connecting a DVD Player, DTV Set-Top Box (480i, 480p, 1080i) The rear panel jacks on your TV make it easy to connect a DVD player (or DTV Set-Top Box) to your TV. Connecting to Y, PB, PR 1 Connect a set of audio cables between the DVD audio in jacks on the TV and the AUDIO OUT jacks on the DVD player (or DTV Set-Top Box). 2 To enable Component video viewing, connect video cables between the Y, PB, and PR inputs on the TV and Y, PB, and PR (or Y, CB, CR) outputs on the DVD player (or DTV Set-Top Box). Note: For an explanation of Component video, see your DVD player’s (or DTV Set-Top Box) owner’s instruction. Connecting to regular audio and video jacks 1 Connect a set of audio cables between the AUDIO IN jacks on the TV and the AUDIO OUT jacks on the DVD player (or DTV Set-Top Box). 2 Connect video cables between the VIDEO OUT jack on the DVD player (or DTV Set-Top Box) and the VIDEO IN jack on the TV. Note: This figure shows the Standard Connector-jack panel. The actual configuration on your TV may be different, depending on the model. INSTALLATION 2.9 CHAPTER TWO: INSTALLATION 1 Connect a set of audio cables between the DTV Set-Top Box audio in jacks on the TV and the AUDIO OUT jacks on the DTV Set-Top box. 2 To enable Component video viewing, connect video cables between the Y, PB, and PR inputs on the TV and Y, PB, and PR (or Y, CB, CR) outputs on the DTV Set-Top box. Note: For an explanation of Component video, see your DTV Set-top box’s owner’s instruction. INSTALLATION Connecting a DTV Set-Top Box Connecting to Y, PB, PR (480p, 1080i) Connect the Y, PB, and PR video outputs of the set-top box to their corresponding inputs on the TV. Next, connect the Left and Right audio from the set-top box to the corre-sponding L and R terminals on the TV. (The connections for a typical set-top box are shown below.) CHAPTER TWO: INSTALLATION 2.10 Connecting to DVI (Digital Visual Interface)(480p, 720p, 1080i) By inputting a high-bandwidth Digital Content Protection high-definition picture source to the DVI INPUT jack on the TV, high-definition pictures can be displayed on the screen in their digital form. (This DVI INPUT jack is for use in the future when High-bandwidth Digital Content Protection DTV decoder, DVD players and D-VHS are put on the market.) 1 Connect a set of audio cables between the DTV Set-Top Box audio in jacks on the TV and the AUDIO OUT jacks on the DTV Set-Top box. 2 Connect a set of audio cables between the AUDIO INPUT jacks on the TV and the AUDIO OUT jacks on the Set Top Box. 3 Connect a DVI cable between the DVI INPUT jack on the TV and the DVI OUT jack on the Set Top Box. Note: For an explanation of Component video, see your DTV Set-top box’s owner’s instruction. INSTALLATION Notes • The DVI INPUT jack can only be use with 480p, 720p, and 1080i picture signals. Set the DTV decoder DVI OUTPUT jack output setting to 480p, 720p or 1080i. For detailed information, refer to the Set Top Box instruction manual. • The DVI INPUT jack is not compatible with the picture signal of a personal computer. • Use a DVI 25-pin cable (commercially available) in order to digitally connect the TV with a DTV decoder. INSTALLATION Installing Batteries in the Remote Control 1 Slide the back cover all the way out to open the battery compartment of the remote control. Ў Make sure to match the “+” and 2 “–” ends of the batteries with the Install two AAA size diagram inside the compartment. batteries. Ў Remove the batteries and store 3 them in a cool, dry place if you won’t Replace the cover. be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the Batteries last for about one year.) 2.11 CHAPTER TWO: INSTALLATION Chapter Three OPERATION Turning the TV On and Off Press the Power button. You can also use the POWER button on the front panel. Plug & Play Feature When the TV is initially powered On, five basic customer settings proceed automatically and subsequently: Setting the language, Ant. input check, and Auto program/Setting the Clock. 1 Press the Power button on the remote control. The message “Plug & Play” is displayed. It flickers for a little while and then the “Language” menu is automatically displayed. 2 Press the VOL + or VOL button to select the desired language. Press the Menu button to enter the language, and then the “ANT/CATV” menu is automatically displayed. Language : English Plug & Play Convergence Caption Time Auto Clock Set V-Chip Function 3 Press the VOL + or VOL button to select the desired to video signal source. Press the Menu button to enter the video signal source, and then the “Ant Input check” is automatically displayed. Antenna : A ANT/CATV : ANT Auto Program Fav. Channel Fine Tune : 00 Add/Erase Labeling : ---- Channel continued... CHAPTER THREE: TV OPERATION 3.1 OPERATION 4 Make sure that the antenna is connected to the TV. And then press the VOL + or VOL -button to activate “Aut...
Este manual também é adequado para os modelos :TV - HCN4727W (3.42 mb)
TV - HCN436W (3.42 mb)