Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
(For information on connecting equipment, see pages 2.1 – 2.8.) OE PERFECT FOCUS Press to adjust for the optimum picture set in the Factory. . VIDEO INPUT jack Use to connect a video signal from a camcorder or a video game. . AUDIO INPUT jacks Use to connect the audio signals from a camcorder or video game. . S-VIDEO INPUT jack Use to connect an S-Video signal from a camcorder or a video game. Using the Component Shelf (HCM5525WB/HCM653WB/HCM553WB/HCM474W/HCM556W) You can place a VCR, a DVD player, etc. on the Component Shelf. HCM5525WB / HCM653WB / HCM553WB / HCM474W 1 Press the symbol “ “ in the center of the Component Shelf door. 2 As shown in figure below, hold the center of door and lift it up. 3 After placing a component on the shelf, hold the center of door and pull it down as shown in figure below. 4 Shut the door by pressing the “ “ symbol. . Note: When placinga component on the shelf, make sure it is no more than 5 inches tall and leave one inch of space from the front and sides for ventilation. HCM556W 1 Hold the center of the door and lift it up in the direction arrow as shown in figure. 2 After placing a TV (or VCR, DVD, etc.) on the shelf, hold the center of the door and pull it down as shown in figure. 1.3 CHAPTER ONE: YOUR NEW TV CHAPTER ONE: YOUR NEW TV 1.4 YOUR NEW TV Rear Panel Jacks Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a DVD player. Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a DVD, 2 VCRs, etc.) For more information on connecting equipment, see pages 2.1 – 2.8. OE ANTENNA terminals Two independent cables or antennas can be connected to these terminals. Use ANT-A and ANT-B terminals to receive a signal from VHF/UHF antennas or your cable system. Use the ANT-A OUT terminal to send the signal being received by the ANT-A terminal out to another component (such as a Cable Set Top Box). The PIP channel can be received only when a signal source is connected to ANT-A. . AUDIO-VIDEO MONITOR OUTPUT jacks Connect to the audio/video input jacks of a recording VCR. Note: The monitor out does not operate in DVD or DTV mode. . VIDEO INPUT jacks Connect to the video output jacks of VCRs, DVD players and similar devices (Two sets are available: Video1 and Video2). . AUDIO INPUT jacks Connect to the audio output jacks of VCRs, DVD players and similar devices. . S-VIDEO INPUT jack Connect to an S-VHS VCR or DVD player. O COMPONENT 1(480i, 480p, 1080i) AUDIO/VIDEO INPUT jacks Connect a source that outputs 480i/480p/1080i Y,PB and PR signals, such as a DVD (or DTV Set- Top Box. . COMPONENT 2, 3(480p, 1080i) AUDIO/VIDEO INPUT jacks Connect a source that outputs 480p/1080i Y, PB and PR signals, such as a DTV Set-Top Box. (The Component3 jack is available on PCL545R/ HCM422W / HCM474W / HCM553WB / HCM653WB) YOUR NEW TV Remote Control You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR and cable box. See page 4.20 for details. OE Power Turns the TV on and off. . +100 Press to select channels over 100. For example, to select channel 121, press “+100,” then press “2” and “1.” . Still(Main) Press to stop the action during a particular scene. Press again to resume normal video. . CH and CH (Channel Up/Down) Press CH or CH to change channels. VOL -, VOL + Press increase or decrease the volume. . Sleep Press to select a preset time interval for automatic shutoff. O Display Press to display the current channel and the audio-video settings. . Aspect Press to change the screen size. ” BBE BBE is a built-in effect that adds clarity, punch and dynamics to the sound. ’ MTS (Multichannel Television Stereo) Press to choose stereo, mono or Separate Audio Program (SAP broadcast). . Mute Press to temporarily cut off the sound. O Pre-CH Tunes to the previous channel. . TV/Video All the inputs connected to the external component jacks will be shown in regular sequence. O Menu Displays the main on-screen menu. U Caption Controls the caption decoder. . PIP Activates picture in picture. . Perfect Focus Press to adjust for the optimum picture set in the Factory. . Fav. CH (Favorite Channel) Press to switch between your favorite channels. 1.5 CHAPTER ONE: YOUR NEW TV YOUR NEW TV Remote Control (continued) . ANT A/B Press to select the ANT A or ANT B. . R.surf Press to automatically return to a preferred channel after a user- preset time delay. . S.Mode Adjust the TV sound by selecting one of the preset factory settings (or select your personal, customized sound settings). . P.Mode Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings). . VCR controls Controls VCR tape functions: Rewind, Play, Fast Forward, Stop, Pause. . PIP Controls Source Press to select one of the available signal sources for the PIP window. ...
Este manual também é adequado para os modelos :TV - HCM553WB (5.16 mb)
TV - HCM5525WB (5.16 mb)
TV - HCM474W (5.16 mb)
TV - HCM4715W (5.16 mb)