Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
O VOL -, VOL + Press to decrease or increase the volume. . MUTE Press to temporarily cut off the sound. ” Anynet Please refer to the Anynet Owner’s Instructions. ’ MENU Displays the main on-screen menu. . oe/v/†/… Controls the cursor in the menu. O VCR/DVD Controls Controls VCR/DVD functions: Rewind, Stop, Play/Pause, Fast Forward. . MODE Selects a target device to be controlled by this remote control (i.e., TV, Samsung STB, VCR, Cable box or DVD). O PRE-CH Tunes to the previous channel. U CH , CH Press to change channels. . SOURCE Each time the button is pressed, all the inputs connected to the external component jacks will be shown in regular sequence. . INFO Press to display information on the TV screen. . EXIT Press to exit the menu. . ENTER While using the on-screen menus, press ENTER to activate (or change) a particular item. English - 12 YOUR NEW TV Remote Control (continued) . CH. LIST Displays the channel list. . FAV. CH (Favorite Channel) Press to switch to your favorite channels. . P.MODE Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings). . P.SIZE Press to change the picture size. . S.MODE Adjust the TV sound by selecting one of the preset factory settings (or select your personal, customized sound settings). ± SET Used during set up of this remote control, so that it will work compatibly with other devices (VCR, Samsung Set-Top box, Cable box, DVD, etc.) . ADD/DEL Press to add or erase channels in the TV’s memory. Use to memorize or erase the channel fine tuning. – SLEEP Press to select a preset time interval for automatic shut off. — SELF FOCUS Press to adjust for the optimum picture set in the factory. . CAPTION Press to view closed caption information. ® BBE BBE is a built-in effect that adds clarity, punch and dynamics to the sound. . MTS (Multichannel Television Sound) Press to choose “Stereo”, “Mono” or “SAP (Secondary Audio Program)”. µ RESET If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds. Re-insert the batteries and try using the remote control again. English - 13 Chapter Two Chapter Two INSTALLATION Connecting VHF and UHF Antennas If your antenna has a set of leads that look like this, see “Antennas with 300-ohm Flat Twin Leads,” below. If your antenna has one lead that looks like this, see “Antennas with 75-ohm Round Leads,” on page 15. If you have two antennas, see “Separate VHF and UHF Antennas,” on page 15. Antennas with 300-ohm Flat Twin Leads If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300ohm twin flat leads, follow the directions below. 1 Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws. 2 Plug the adaptor into the “ANT 1 IN (Air)” terminal on the rear panel. English - 14 INSTALLATION Antennas with 75-ohm Round Leads Plug the antenna lead into the “ANT 1 IN (Air)” terminal on the rear panel. Separate VHF and UHF Antennas If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires a an optional combiner-adaptor (available at most electronics shops). 1 Connect both antenna leads to the combiner. 2 Plug the combiner into the “ANT 1 IN (Air)” terminal on the rear panel. English - 15 INSTALLATION Connecting Cable TV You can connect different cable systems to your TV, including cable without a cable box, and cable with a cable box that descrambles some or all channels. Cable without a Cable Box If you want to connect cable, and you do not need to use a cable box: Plug the incoming cable into the “ANT 2 IN (Cable)” terminal on the rear panel. Cable with a Cable Box that Descrambles All Channels oe This terminal might be labeled 1 “ANT OUT”, “VHF OUT”, or Find the cable that is simply “OUT”. connected to the ANTENNA OUT terminal on your cable box. 2 Connect the other end of this cable to the “ANT 2 IN (Cable)” terminal on the rear panel. English - 16 INSTALLATION Connecting to a Cable Box that Descrambles Some Channels If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.) oe This terminal might be labeled 1 “ANT IN,” “VHF IN,” or simply, Find and disconnect the “IN.” cable that is connected to the ANTENNA IN terminal on your cable box. 2 Connect this cable to a two-way splitter. Connect a coaxial cable between an OUTPUT Incoming Cable Splitter terminal on the splitter and the IN terminal on the cable box. 3 Connect the last coaxial cable between the OUT terminal on the RF (A/B) switch and the VHF/UHF terminal on the rear of the TV. Connect a coaxial cable between the ANTENNA OUT terminal on the cable bo...
Este manual também é adequado para os modelos :TV - HC-R5245W (2.84 mb)
TV - HC-R4755W (2.84 mb)
TV - HC-R4745W (2.84 mb)