Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
17. Tilt/Stability - All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabinet design. • Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product. • Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury. 18. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer. 19. Power Lines - An outdoor antenna should be located away from power lines. 20. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure below. 21. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.comply with recommended international global safety standards for tilt and stability properties of its cabinet design. 22. Battery Usage CAUTION - To prevent battery leakage that may result in bodily injury, property damage, or damage to the unit: • Install all batteries correctly, with + and - aligned as marked on the unit. • Do not mix batteries (old and new or carbon and alkaline, etc.). • Remove batteries when the unit is not used for a long time. ANTENNA LEAD IN WIRE ANTENNA DISCHARGE UNIT (NEC SECTION 810-20) GROUNDING CONDUCTORS (NEC SECTION 810-21) GROUND CLAMPS POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H) GROUND CLAMP ELECTRIC SERVICE EQUIPMENT Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Example of Antenna Grounding as per NEC - National Electric Code If Cable TV signal into your home is a single cable (75 ohm) the connection to the TV is easy. 1Connect the Cable TV cable directly to the 75. jack on the TV. Basic Cable TV Connection Basic Antenna Connection 75. 75. Cable TV Signal RF Coaxial Cable 75. Rear of TV Acombination antenna receives normal broadcast channels (VHF 2-13 and UHF 14-69). Your connection is easy since there is only one 75. (ohm) antenna plug on the back of your TV - and that’s where the antenna goes. 1If your antenna has a round cable (75 ohm) on the end, then you're ready to connect it to the TV. Go to step 2. If your antenna has flat twinlead wire (300 ohm), you first need to attach the antenna wires to the screws on a 300 to 75 ohm adapter (not supplied with TV). 2Push the round end of the adapter or antenna cable onto the 75. jack on the rear of the TV. If the round end of the antenna cable is threaded, screw it down tight. 1 75. 75. Combination VHF/UHF Antenna (Outdoor or Indoor) Twin Lead Wire Round Cable 75. Rear of TV 2 Cable Box Connections TO TV/VCR CABLE IN IR USB DVD-D OUT AUDIO IN SPDIF VIDEO IN OUT R L S-VIDEO AUDIO OUT TV PASSCARD Y Pb Pr OPTICAL SPDIF 2 1 75. 75. 3 Jack Panel Back of Cable Box Cable Signal IN from the Cable Company Round 75. Coaxial Cable Jack Panel Back of TV If you cable signal uses a cable box or decoder, follow the easy steps below to complete the connection. Cable Box (w/RF In/Outputs): This connection will be mono. 1Connect the Cable Company supplied cable to the signal IN(put) plug on the back of the Cable Box. 2Using a separate round coaxial cable, connect one end to the OUT(put) (TO TV) plug on the back of the Cable Box. 3Connect the other end of the round coaxial cable to the 75. input on the back of the television. Screw it down finger tight. NOTE: If applicable, set the OUTPUT CHANNEL SWITCH on the back of the cable box to CH 3 or 4. Tune the TV to the same channel and change channels at the cable box. In some cases, the cable box will automatically tune to either channel 3 or 4, change channels until the picture appears. ANTENNA OUT ANTENNA IN VIDEO AUDIO IN IN OUT OUT o VOLUME + CHANNEL MENU VIDEO AUDIO POWER o VOLUME + MENU CHANNEL POWER VIDEO AUDIO 1 2 35 3 3 Front AV (Audio/Video) Input Connections Audio and Video Front Inputs are available for a quick connection of a VCR, to playback video from a camera, or attach a gaming device. Use the AV button on the remote cont...