Log:
Assessments - 5, GPA: 4.4 ( )

Instruções de Operação LG, Modelo LSW200BXG

Fabricante : LG
Arquivo Tamanho: 6.46 mb
Arquivo Nome :
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Assemble the guide spacer and the guide spacer screw in order as shown in the picture. - Assemble the guide spacer to the set by tightening the screw. - Tighten the screw until the set, guide spacer and the screw are fully pressing against one another. - Use the "+" driver (Manual or motorized) when tightening the screw. 3 How to install the wall mount > When you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier to install the product. > When installing the product on a masonry wall, turn the 8 screws on the A part counterclockwise to separate the screw and bracket. > After aligning the wall bracket to the location to install, mark the part to screw on the wall and then remove the wall bracket. > Refer to page 4 to attach the wall bracket. > Use a level to check whether the wall mount is level. Separate the wall mount screw. 2 How to attach to masonry walls - Check the material of the wall and the thickness of the finishing. - When installing the product on the wooden wall, refer to page 5. - When installing the product on wall material not designated, install the product so that each fixated location can withstand the pull out load of 70kgf (686N) and shear load of 10kgf (980N) or above. - Use the O8mm drill bit for concrete and hammer (Impact) drill. Please follow the below direction. a. Use a drill bit O8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm b. Clean the drilled hole. c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.) d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward. e. Align the wall mount bolt to the hole and tighten it. At this time, the bolt must be tightened with torque of 45kgf/cm or above. Anchor Wall mount screw - Tools you will need : Phillips head "+" driver(Manual or motorized) O4mm drill bit for wood or steel / Level / Stud finder / Drill. You may also need an 8mm socket wrench or an 8mm drill bit for concrete. - Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. a b c d e A Guide spacer screw Install the PVC washer on models 37/42/47LE53*, 37/42/47LE55*, 42/47/55LX65*, 42/47/55LX68* Install the wall mount only after attaching the PVC washer on the back cover of the TV. Guide spacer 5 ENGLISH > If the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the closest location. But, do not change 2 or more locations from the designated spot. > LSW200B/LSW200BG/LSW200BX/LSW200BXG : Assemble the wall mount screw on 1 left and 1 right location on the top part and 1 left and 1 right location on the bottom part. > LSW400B/LSW400BG : Assemble the wall mount screw on 2 left and 2 right locations on the top and 1 left and 1 right location on the botto...

Este manual também é adequado para os modelos :
TV - LSW200B (6.46 mb)
TV - LSW200BG (6.46 mb)
TV - LSW200BX (6.46 mb)
TV - LSW400B (6.46 mb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias