Assessments - 6, GPA: 4.2
(
)
)
|
Facilidade de uso
Each time the software detects an error it is stored within the NVM. See Table 2. Table 1 How to enter into Table 2 Error Message LED Code No error 00 Reserved 01 OCP ( Over Current Protection ) 02 Not Used 03 No Vertical Sync 04 IKR Error at power on 05 IIC bus clock and/or data lines low at power on 06 NVM no IIC bus acknowledge at power on 07 Not Used 08 Tuner no acknowledge at power on 09 Sound Processor Error 10 Jungle controller 8 volts error 11 1. Turn on the main power switch of the TV set and enter into the‘Stanby Mode’. 2. Press the following sequence of buttons on the Remote Commander. i+ - 5 (ON SCREEN (DIGIT 5) (VOLUME -) (TV) DISPLAY) 3. The following table will be displayed indicating the error count. Flash Timing Example : e.g. error number 3 Table 2 StBy LED ONON ON ERROR MENU OFF OFF E02 OCP (0, 255) 0 E03 OVP N/A (0, 255) 0 E04 VSYNC (0, 255) 0 E05 IKR (0, 255) 0 E06 IIC (0, 255) 0 E07 NVM (0, 255) 0 E08 JUNGLE (0, 255) 0 E09 TUNER (0, 255) 0 E10 SOUNDP (0, 255) 0 E11 8V (0, 255) 0 WORKING TIME HOURS 2 MINUTES 11 Note: To clear the error count data press ‘80’ on the Remote commander. 5 The operating instructions mentioned here are partial abstracts from the ‘OperatingInstruction Manual’. The page numbers of the ‘Operating Instruction Manual’ remainas in the manual. Do you want to startautomatic tuning?YesNo OK K Switching On the TV and Automatically Tuning The first time you switch on your TV, a sequence of menu screen appear on the TV enablingyou to: 1) choose the language of the menu screen, 2) choose the country in which you wishto operate the TV, 3) adjust the picture slant 4) search and store all available channels (TVBroadcast) and 5) change the order in which the channels (TV Broadcast) appear on thescreen.However, if you need to change any of these settings, you can do that by selecting theappropriate option in the (Set Up menu) or by pressing the Auto Start Up Buttonon the TV set. 1 Connect the TV plug to the mains socket (220-240V AC,50Hz)Press the on/off button on the TV set to turn on the TV. The first time you press this button, a Language menu displays automatically on the TV screen. 2 Press the or button on the remote control to selectthe language, then press the OK button to confirm yourselection. From now on all the menus will appear in theselected language. LanguageSelect Language:4SvenskaNorskEnglishNederlandsFrancaisItaliano$ OK K GB 3 The Country menu appears automatically on the TVscreen. Press the or button to select the country inwhich you will operate the TV set, then press the OK button to confirm your selection. If the country in which you want to use the TV set• does not appear in the list, select “-” instead of acountry. In order to avoid wrong teletext characters for• Cyrillic languages we recommend to select Russiacountry in the case that your own country does notappear in the list. Country4SverigeNorge-ItaliaDeutschlandOsterreich$Select country: OK 4 Because of the earth’s magnetism, the picture might slant.The Picture Rotation menu allows you to correct thepicture slants if it is necessary. a) If it is not necessary, press or to select Not necessary and press OK. b) If it is necessary, press or to select Adjust now, then press OK and correct any slant of the picturebetween –5 and +5 by pressing or Finally press. OK to store. If picture slants, pleaseadjust picture rotationNot necessaryAdjust now OK KK 5 The Auto Tuning menu appears on the screen. Press theOK button to select Yes. 6The TV starts to automatically search and store allavailable broadcast channels for you.This procedure could take some minutes. Please bepatient and do not press any button. Otherwise theautomatic tuning will not be completed. If no channels were found during the auto tuningprocess then a new menu appears automatically onthe screen asking you to connect the aerial. Pleaseconnect the aerial (see page 6) and press OK. The auto tuning process will start again. 7 After all available channels are captioned and stored,the Programme Sorting menu appears automaticallyon the screen enabling you to change the order inwhich the channels appear on the screen. a) If you wish to keep the broadcast channels in thetunned order, go to step 8. b) If you wish to store the channels in a different order:1 Press the or button to select the programmenumber with the channel (TV Broadcast) you wishto rearrange, then press the button. 2 Press the or button to select the newprogramme number position for your selectedchannel (TV Broadcast), then press . 3 Repeat steps b)1 and b)2 if you wish to change the order of the other channels. 8 Press the MENU button to remove the menu from thescreen. Your TV is now ready for use Programme: 01 System: B/G Channel: C21 Auto TuningSearching... No channel foundPlease connect aerialConfirm OK K SECTION 1 GENERAL 6 Programme SortingSelect channel:Exit: MENUProgramme:01 TVE 02 TVE2 03 TV3 04 C33 05 C27 06 C58 OK Programme SortingSelect new position:Exit: MENUProgramme:01 T...
Este manual também é adequado para os modelos :TV - FD TRINITRON KV-21FX30B (8.07 mb)