Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
20. 24. 27. Picture Modes l l l l Trilingual OSD l l l l 6 Instruction Manual Front and Rear Unit Profiles AT1302 Front panel See the figure at right. ANTENNA IN VIDEO IN AUDIO IN MAIN POWER SWITCH INFRARED SENSOR POWER LED TV/VIDEO SELECT MENU SELECT VOLUME ADJUST CHANNEL SELECT Rear panel VIDEO OUT AUDIO OUT 7 Standard - AT1302, AT2002, AT2402, AT2702 Front and Rear Unit Profiles (continued) AT2002 Front panel Side panel AV IN on the side panel MAIN POWER SWITCH INFRARED SENSOR POWER LED MENU CHANNEL SELECT TV/VIDEO SELECT SELECT VOLUME ADJUST Rear panel AUDIO IN VIDEO IN RF ANTENNA IN AUDIO OUT VIDEO OUT See the figure at right.. 8 MAIN POWER SWITCH INFRARED SENSOR POWER INDICATOR VIDEO MENU -VOL + RF ANTENNA IN See the figure at right.. -CH + TV/VIDEO SELECT MENU SELECT VOLUME ADJUST CHANNEL SELECT Instruction Manual Front and Rear Unit Profiles (continued) AT2402 Front panel Rear panel 9 Standard - AT1302, AT2002, AT2402, AT2702 Front and Rear Unit Profiles (continued) AT2702 Front panel INFRARED SENSOR MAIN POWER POWER INDICATOR SWITCH VOLUME CHANNEL SELECT FRONT A/V INPUT TV/VIDEO MENU ADJUST SELECT SELECT Rear panel ANTENNA IN See the right figure. 10 Instruction Manual Remote Control Features Function (p. 11, ) Used for volume control and child lock Keypad (p.11) Used to select channels by number 100+ (p. 11) Used for channels over 99 Timer (p. 13) Accesses the Timer menu Scan (p. XX) The TV will scan all active channels Picture (p. XX) Selects the various Picture Modes Recall (p. XX) Returns to the last channel viewed CC (p. XX) Activates Closed Captioning Standby (p. 11) Turns the TV On or Off CH + / ( p. 11) Used to adjust the current channel VOL + / ( p. 11) Used to adjust the volume up or down Display (p. 11) Brings up the TV display Arrows Used to navigate the TV menus (p. 12, 13, 14, 15) Menu Accesses the TV menus (p. 12, 13, 14, 15) Mute Mutes or restores the TV volume (p. 11) Video Cycles through the Video/Air modes (p. XX) FUNCTION STANDBY KEYPAD 100+ TIMER SCAN PICTURE RECALL CH + / - VOL + / - DISPLAY ARROWS MENU MUTE VIDEO CC 11 Standard - AT1302, AT2002, AT2402, AT2702 INSTALLATION -Please read the safety instructions in this manual completely before installation. - Install your TV in an area where direct sunlight will not fall upon the screen. -Soft, indirect light is best for television viewing. -Allow enough space (at least 4 in.) between the TV and any wals or enclosures for proper ventilation. -The optimum television viewing distance is 5-7 times the screen’s vertical length: 13. - 5 to 7 feet 24. - 10 to 14 feet 20. - 8 to 13 feet 27. - 13 to 16 fet Auto-Degaussing Color television can be easily affected by magnetism, which shows as color distortion on the screen. If your TV is affected by nearby magnetic components or appliances, press the MAIN POWER SWITCH on the front of the TV to power off your TV for at least 1 hour. The built-in auto-degaussing circuit will eliminate the magnetic interference. Connecting the Antenna 75-ohm coaxial cable (not supplied) 300-ohm twin-lead cable (not supplied) OR OR Antenna adapter (not supplied) U/V mixer (not supplied) Notes: 1. It is recommended that a 75 ohm coaxial cable be used in order to eliminate interference and noise which may occur due to nearby radio transmissions. 2. The antenna cable should not be tied together with other wiring. 3. Set up a lightning rod and check it regularly when an outdoor antenna is used. 1. Remove the battery compartment lid. 2. Insert two AAA batteries (included.) Make sure the positive (+) and negative (-) polarities are correctly aligned. 3. Reattach the battery lid. 1. Alkaline batteries are recommended for longer life. 2. Always replace both batteries at the same time. 3. Do not expose batteries to fire or break them open. 4. To avoid battery leakage, remove batteries from the remote control Remote Control Battery Installation VHF UHF or Cable VHF UHF RF Input (back of TV unit) Notes: when it is not to be used for a long period of time or the batteries are exhausted. 12 Instruction Manual INSTALLATION (continued) Connecting A/V Equipment The following are diagrams showing basic instructions for attaching external equipment, like a VCR or DVD player, to your TV set. Please refer to operation manuals of external audio/video equipment that will be connected to your set for additional instructions. PLEASE TURN ALL POWER IS OFF BEFORE CONNECTING DEVICES TOGETHER. Connect VCR’s RF OUT terminal to the ANTENNA IN jack located on the real panel of the TV. Coaxial Cable VCR with Modulator AUDIO/VIDEO OUT DVD Player Camcorder VCR AUDIO/VIDEO IN VCR With S - VIDEO Terminal VIDEO Yellow White Yellow White Yellow White Yellow White ANTENNA IN AT2402, AT2702 only Do NOT connect the yellow composite video terminal if using the S-Video terminal. Actual back of TV may vary. Please see pgs. 9-12 for your TV.s back panel illustration. Output From TV to Device Input From Device to TV The front or side terminals may be eas...
Este manual também é adequado para os modelos :TV - AT1302, AT 2002, AT2402, AT2702 (302.83 kb)
TV - AT2402 (302.83 kb)
TV - AT2702 (302.83 kb)