Assessments - 3, GPA: 4.3 ( )

Fabricante : Hitachi Arquivo Tamanho: 2.33 mb Arquivo Nome : Língua de Ensino:

IMPORTANT Figure 2. Connecting the DTV receiver with component 22 video connections. Connecting an External Digital TV (TV or HTV) Receiver, cont. Figure 1. Connecting the DTV receiver with RGB video • See Appendix B for RGB video signal compatibility information. • For digital audio connections, see your DTV Receiver and A/V Receiver Owner’s Guides. IMPORTANT External DTV Receiver with RGB Video Connections (Figure 1) 1. Connect the outside antenna, cable, or satellite to ANT, or SATELLITE IN on the DTV receiver (see your DTV receiver owner’s guide for instructions, and cable compatibility). 2. Connect the incoming terrestrial antenna, or cable (not satellite) to ANT-A on the TV back panel (a coaxial splitter, available at most electronic supply stores, may be required to complete this installation). 3. Connect RGB cables for the DTV receiver to Input-DTV on the TV back panel. Note: You may need to set the Input-DTV assignment to RGB instead of Y/Pr/Pb. Refer to the Edit NetCommand™ Setup for instructions on changing this setting. DTV Receiver / TV Back Panel • G (green) to Y/G • R (red) to Pr/R •B (blue) to Pb/B Note: If the DTV receiver has outputs for H and V sync, connect as listed below (DO NOT connect if DTV receiver uses “Sync on Green” • H (horizontal sync) to H • V (vertical sync) to V 4. Connect the L (left) and R (right) audio cables from the DTV receiver to Input-DTV AUDIO on the TV back panel. 23 24 Connecting a Computer with a VGA Monitor Output Connecting a Computer (Figure 1) 1. Connect VGA Monitor Out from the computer to VGA Input on the TV back panel using a VGA compatible monitor cable. See Appendix B for VGA signal compatibility. 2. Connect the L (left) and R (right) audio cables from the computer to VGA AUDIO on the TV back panel. In cases where your computer’s audio output is a single mini- jack, a Connecting the IR-Home Theater Control and IR Repeater splitter is needed to complete this connection. Note: To utilize the benefits of a digital A/V receiver, connect your computer’s digital audio out, if available, to a digital input on your digital A/V receiver. (Figure 2) IR Emitter-Home Theater Control These emitters are not IR repeaters; they are used by the NetCommand™ feature to control supported devices. 1A. Connect the IR emitter to IR Emitter-Home Theater Control on the TV back panel. OR ... IR Emitter-Repeater These emitters are not used by NetCommand™, but will repeat any IR command received by the TV. These emitters allow the TV to be the remote control sensor for other devices outside the range of the hand-held remote control. Do not use these repeaters with devices that can receive the remote control signal directly, as the signals can interfere with each other. 1B. Connect the IR emitter to IR EMITTER REPEATER on the TV back panel. Steps 2-4 (Apply both 1A and 1B) 2. Place the IR emitter cable under or along the side of the A/V device. Place the IR lens directly in front of the A/V device’s infrared signal receiver. Infrared signal receivers are usually behind the front translucent panel of the device. Figure 1. Connecting a computer with a VGA monitor output. CAUTION: To ensure continued FCC compliance, the user must use a shielded video interface cable with bounded ferrite cores, when using the VGA input. Figure 2. Connecting the IR Home Theater Control and/ or Repeater. 3. Place unused transmitters in an out-of-theway location. 4. For permanent installation of the IR emitter cable, use the included adhesive tape to secure the bottom of the emitter to the anchoring object of your choice. IMPORTANT NOTES WARNING: When using the VGA input, do not leave stationary, toolbar, or partial images on-screen for extended periods of time. Mix the types of pictures shown. Uneven picture tube aging is NOT covered by your warranty. The VGA capability of this television is designed for occasional use ONLY. It is not meant to be used as a work station or to view static or odd-shaped images for an extended period of time. Any device connected to your television via the VGA port, including, but not limited to, personal computer, game system, or digital set-top box, must have its screen saver function activated to prevent damage to the television. We DO NOT recommend the use of any external device that does not have a screen saver function with this television. We recommend that screen saver activation time be set to less than five minutes when using a device through the VGA port. You should also use lower brightness and contrast settings. If your computer programs allow, toolbars should be set to hidden mode. Please remember most computer programs and video game systems display static images, such as boxes, buttons, tool bars, and game scores that can damage the television if used for extended periods of time, repeatedly, or frequently. The VGA input will automatically select the “Standard” screen format and fill the screen. No other formats are available with the VGA Input. Standard tele...

Baixe o seu

Para fazer o download, introduza 2 dígitos :